Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. • This appliance was set at the factory to operate at 120 Volts. Refer to Operating Instructions Section of this manual for conversion to 240 Volt operation. • Be sure dual voltage selector is in the correct voltage position before operation. Before plugging iron into outlet, read the information about dual voltage operation in the “Voltage” section of this manual. • To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits a polarized outlet only one way; if the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. SAVE THESE INSTRUCTIONS (Ink) (Ink) Congratulations on Your Purchase of a SUNBEAM@ Iron! Irons are designed to provide the utmost in quality, ease of use and convenience. This Iron offers the following features: A. SHOT OF STEAM’ BUTTON -for stubborn wrinkles B. WATER TANK RELEASE BUTTON -to easily fill the water tank C. FABRIC SELECT DIAL -adjusts temperate for various fabric types D. TANGLE-FREE CORD -keeps the power cord off the fabric and out of the way E. VOLTAGE SELECTOR SWITCH -for international travel F. HANDLE RELEASE BAR -automatically opens and locks handle into place G. NON-STICK SOLEPLATE -prevents starch residue and fabrics from sticking H. HANDLE RELEASE BUTTON -collapses and locks handle for compact storage I. WATER TANK -accepts tap water and eliminates the need for distilled water VOLTAGE Be sure the dual voltage selector is in the correct position before operating. In North America the voltage selector switch should be placed in the 120 volt position. This appliance was set at the factory to operate at 120 volts (See Figure 1). HANDLE To unlock the handle, press the handle FIGURE release bar (See Figure 2). The handle will automatically rise to the upright position and lock into place. WATER FILL IMPORTANT: Always turn the fabric select dial to OFF and disconnect iron from electrical outlet before FIGURE 2 filling or emptying the water tank. Slide the water tank release button backwards (See Figure 3) and hold into position with one hand. Lift water tank to remove from iron with the other hand (See Figure 4). (Ink) (Ink) FIGURE 3 Lift the fill hole cap on the water tank and fill with clean tap water (See Figure 5). Replace the fill hole cap, ensuring th it is fastened securely. Snap the front of the water tank into the iron base (See Figure 6). Slide the water tank release button FIGURE 5 backwards and hold into position with one hand. Press back of water tank into position with other hand and release the button to lock the tank in place. IRONING Plug iron into an electrical outlet. Use the “Fabric Setting” chart to determine the best setting and method for the fabric you plan to iron. Move the fabric select dial to the desired setting. The temperature can be adjusted by turning the dial clockwise until the indicator mark is aligned with the proper setting. Allow the iron to heat for approximately five minutes. While the iron is heating, make sure it is sitting on its heel rest and handle on a stable, protected surface. FIGURE 6 For particularly stubborn creases, the SHOT OF STEAM@ function can be used if the temperature adjustment dial is on the hottest setting. Set the fabric select dial to the “cotton/linen” setting. Wait for the iron to reach temperature, press the steam button firmly and release. FABRIC CHART FABRIC Acetate, Nylon, Polyester, Rayon SETTING Synthetic IRON RECOMMENDATIONS Iron garment inside out while still damp. Acrylic, Silk Silk Iron garment inside out. Wool Wool Iron garment inside out or use ironing cloth? Cotton, cotton/ Iron dark fabrics inside out to prevent Cotton blends, Linen shine marks. Use SHOT OF Linen feature to remove stubborn wrinkles. *An ironing cloth is a cotton, dry-cleaned cloth that you place over the garment you are ironing to prevent the fabric from looking shiny. CARING FOR YOUR IRON AFTER USE Turning Off Your Iron Turn the temperature select dial to OFF. Unplug the iron from the power source. Storing Your Iron l• Allow iron to cool. Remove water tank from iron and empty water from fill hole. Replace water tank. l• Wipe soleplate with a soft, damp cloth FIGURE 7 to remove residue as required. l• Press handle release button in (See Figure 7) and push handle down to lock into position. l• Loosely loop the power cord around iron and store iron in the travel pouch. Sunbeam Products, Inc. (“Sunbeam”) warrants that for a period of one year from the date of purchase, tbii product will be free from defects in material and workmanship. Sunbeam, at its option, will repair or replace tbii product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product...