Évaluations - 4, GPA: 4 ( )

Fabricant : Philips Taille : 739.14 kb Nom Fichier : 061147f8-c6c8-94c4-ed30-38b6d0631429.pdf Langue d'enseignement:

. Check if the voltage indicated on the type plate corresponds to the local mains voltage before you connect the appliance. . Only connect the appliance to an earthed wall socket. . Do not use the appliance if the plug, the cord or the appliance itself shows visible damage, or if the appliance has been dropped or is leaking. . Check the cord regularly for possible damage. . If the mains cord is damaged, it must be replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard. . Never leave the appliance unattended when it is connected to the mains. . Never immerse the iron and the stand, if provided, in water. . Keep the appliance out of the reach of children. . The soleplate of the iron can become extremely hot and may cause burns if touched. . Do not allow the cord to come into contact with the soleplate when it is hot. . When you have finished ironing, when you clean the appliance, when you fill or empty the water tank and also when you leave the iron even for a short while: set the steam control to position O, put the iron on its heel and remove the mains plug from the wall socket. . Always place and use the iron and the stand, if provided, on a stable, level and horizontal surface. . This appliance is intended for household use only. Preparing for use Filling the water tank Remove the mains plug from the wall socket. Set the steam control to position O (= no steam) (fig. 2). Open the cap of the filling opening. Tilt the iron and fill the water tank up to maximum level (fig. 3). 1 2 3 4 If the tap water in your area is very hard, we advise you to use distilled water. Do not use chemically descaled water. Do not fill the water tank beyond the MAX indication. Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank. 5 Close the cap of the filling opening ('click'). Setting the temperature . The iron may give off some smoke when you use it for the first time. This will cease after a short while. 1 Put the iron on its heel and set the temperature dial to the required ironing temperature by turning it to the appropriate position (fig. 4). - Check the laundry care label for the required ironing temperature. -- 1 1 Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester) Silk -2 Wool -- 3 Cotton, linen If you do not know what kind or kinds of fabric an article is made of, determine the right ironing temperature by ironing a part that will not be visible when you wear or use the article. -Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches. Avoid using the spray function to prevent stains. 2 Put the mains plug in an earthed wall socket. 3 When the temperature light has gone out, wait a while before you start ironing. B The temperature light will go on from time to time during ironing. Using the appliance Steam ironing Set the temperature dial to the recommended position (see section 'Setting the temperature'). - - Set the steam control to the appropriate steam position (fig. 2). A for minimum steam (temperature settings 2 and 3). E for maximum steam (temperature settings 3 to MAX). B The iron will start steaming as soon as the set temperature has been reached. GC2640/GC2620/GC2530/GC2520/GC2510 only: Make sure that there is enough water in the water tank. 1 2 Water may leak from the soleplate if the set temperature is too low (MIN to 2). Ironing without steam 1 2 Set the steam control to position O (= no steam). Set the temperature dial to the recommended position (see section 'Setting the temperature'). Features Spray function Make sure that there is enough water in the water tank. Press the spray button several times to moisten the article to be ironed (fig. 5). Shot of steam You can use the spray function to remove stubborn creases at any temperature 1 2 A powerful shot of steam helps to remove very stubborn creases. The shot-of-steam function only works at temperature settings between 2 and MAX. 1 Press and release the shot-of-steam button (fig. 6). Vertical shot of steam (GC2650/2640/2620/2560/2530/2520) 1 The shot-of-steam function can also be used when you are holding the iron in vertical position. This is useful for removing creases from hanging clothes, curtains, etc (fig. 7). Never direct the steam at people. Drip stop (GC2650/GC2560 only) This iron is equipped with a drip stop function: the iron automatically stops producing steam when the temperature is too low to prevent water from dripping out of the soleplate. When this happens you will hear a click. Automatic shut-off (GC2560 only) The electronic shut-off function automatically switches the heating element off if the iron has not been moved for a while. . The automatic shut-off light starts blinking to indicate that the heating element has been switched off (fig. 8). To let the iron heat up again, pick the iron up or move it slightly. The automatic shutoff light goes out. 1 2 If the temper...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :