Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Pivots up and down to prevent dragging along the fabric. The flexible cord cover protects the cord from fraying. 10 Fabric Setting Indicators 11 Temperature Indicators 12 Power Light 13 Auto-Off Light 14 Anti-Drip Function (not shown) Prevents water spitting when the iron temperature is too low. 15 Built-In Anti-Calcium Filter (not shown) Prevents calcium build-up which prolongs the life of the iron. This iron is for HOUSEHOLD USE ONLY. Plug it into any 120V AC polarized electrical outlet to start ironing! SETTING THE FABRIC AND TEMPERATURE INDICATORS: 1 Press the Electronic Temperature Control to light up at the desired fabric setting on the left side of the LED display panel. Please read the garment label for correct setting. Wait about 1 minute for the iron to heat up. 2 The temperature indicator will light up on the right side of the LED Display Panel as it reaches your desired temperature. 8 Using Your Iron DRY IRONING 1 Choose any of the fabric settings on the LED Display Panel according to your garment label (as described on page 8). 2 Turn the Steam Control Dial to “0”. 3 Place the iron on its heel, standing up and on a stable surface while it's heating up to the desired temperature. 4 Once the steam flow is cut off, you can start ironing. DRY ironing on a low temperature is best on acrylic, nylon, polyester, silk and wool. STEAM IRONING 1 Open the water filling inlet cover. Holding the iron at a slight angle, pour the water slowly into the inlet. The soleplate design allows for ordinary tap water to be used. We recommend using the mix of 50% tap water and 50% distilled water to reduce the hardness. 2 Using the filling flask, fill the tank to a desired level without going over the “MAX” line. Use the see-through water tank to gauge the amount of water going in. 3 When you’re finished, close the inlet cover before continuing. 4 Plug the cord into a polarized 120V AC electrical outlet. Q_ I- 9 a? TOLL FREE: 1-800-798-7398 Using Your Iron ( n——— STEAM ironing on a higher temperature is best on cotton and linen. ANTI-DRIP FEATURE Steam cannot be produced if the soleplate is not hot enough. It may result in water spitting or leaking from the soleplate. This iron is built with an anti-drip feature which reduces water dripping and leaking when ironing at low temperatures. 5 Set the desired fabric/temperature by pressing the electronic temperature control button (as described on page 8) after reading the garment label. 6 Turn the steam control dial to the appropriate steam setting. (See “Ironing Guide” on page 15.) 7 Place the iron on its heel, standing up on a stable, protected surface to allow the iron to heat up for approximately 2 minutes or until the temperature settings on the right side of the LED display panel are lit at the preset temperature. 8 In order to increase the amount of steam, turn the steam control dial to the right within the steam band. When you use extra steam, the iron uses more water, so you may have to fill the tank more often. A Before filling the iron with water, always make sure the cord is not plugged into the electrical outlet. A Be very careful when filling the iron with water. Injuries may occur if you or your family comes in contact with the hot metal parts, hot water or steam. A Never fill the iron with fabric conditioner, starches or any other liquid because these will damage the steam mechanism. Don’t use contaminated water either. A DO NOT aim iron at yourself or anyone else while adjusting steam. Be careful, burns or serious injury may occur. 10 Using the Burst of Steam/X-Tended Steam Burst Button 1 Make sure the water tank is at least 1/2 filled with water. 2 Select the desired fabric and temperature setting after reading the garment label. 3 Place the iron on its heel, standing up on a stable and protected surface so it can heat up for approximately 2 minutes. 4 Turn the steam burst button all the way to the left to the burst of steam position or to the right to the X-Tended steam position. 5 Press the steam burst button or the X-Tended steam button several times to prime the pump. Give an interval of 3 seconds for each burst. Overuse of the steam burst buttons may cause water spitting or weak steam performance. TOLL FREE: 1-800-798-7398 Steam burst and X-tended Steam burst help to remove stubborn wrinkles. Both features can work horizontally and vertically. VERTICAL STEAM 6 The steam burst feature is especially useful to remove wrinkles from hanging clothes, delicate garments and other fabrics. Hold the iron in a vertical position several inches away from the articles and press the steam burst button or the X-Tended steam button several times to prime the pump. A CAUTION: Never iron or steam clothes while they are being worn. A CAUTION: Do not aim iron at yourself or anyone else while using the steam burst feature. Be careful, burns or serious injury may occur. A If t...
Ce manuel est également adapté pour les modèles :Fers - GI490F 12 (2.56 mb)
Fers - GI490F 11 (2.56 mb)
Fers - GI490 12 (2.56 mb)