Évaluations - 4, GPA: 3.3
(
)
)
|
Photos et spécifications Scarlett SC-339S |
Facilité d'utilisation
CAUTION: To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. BEFORE THE FIRST USE • Some parts of the steam iron have been slightly greased and as a result the iron may slightly smoke when switched on for the first time. After a short time this will cease. • Remove protection cover from the soleplate and clean it with a soft cloth. HOW TO USE SETTING TEMPERATURE • Always check first to see whether a label with ironing instructions is attached to the article to be ironed. Follow these instructions in all cases. • Turn the temperature control dial round to set the appropriate temperature indicated in the ironing instructions or in the fabric label. LABEL TYPE OF TEXTILE Do not iron this article • Synthetics, Nylon, Acrylics, Polyester, Rayon •• Wool, Silk ••• Cotton, Linen Maximum temperature (Steam) Insert the mains plug into the wall socket. The indicator light will now turn on. • When the indicator light has gone out you can start ironing • If you set the temperature control to lower setting after ironing at a high temperature, do not recommend ironing before the pilot light switches on again. THE WATER TANK FILLING • Unplug the iron before filling. • Hold the steam iron in the horizontal position. • Slowly pour water through the water inlet. • Do not fill higher than mark on the water tank, in order to avoid spilling out of water. NOTE: Your steam iron is designed to use tap water. However, if the water is very hard, it is advisable to use distilled water. • The water tank should be emptied after each use. NOTE: If you empty the water tank after the steam iron has cooled down, set the steam iron in an upright position on its heel rest, plug it in and set the temperature control dial to the maximal position, heat for 2 minutes. Unplug the steam iron from the power supply. SPRAYING • As long as there is enough water in the water tank, you may use the spray button at any temperature setting either on steam or dry ironing. • Press the spray button several times to activate the pump while you are ironing. STEAM IRONING • Set the temperature control dial to the or “•••” position. • When indicator light is off, the steam iron has reached desired temperature. CAUTION: Avoid coming in contact with ejected steam. DRY IRONING • The steam iron can be used on the dry setting with or without water in the water tank, however it is best to avoid having the water tank too full while dry ironing. • Turn the variable steam control to the minimum position. • Select the setting on the temperature control dial best suited for the fabric to be ironed. CAUTION: If the steam iron has been used for a long time, is hot and there is no water. Do not refill it with water until the steam iron has cooled down. 4 SC-339S BURST OF STEAM • The burst of steam feature provides additional steam for removing stubborn wrinkles. • Turn the temperature control dial to the or “•••” position. • Turn the variable steam control to the maximum position. • Press the powerful steam button to release the burst of steam. WARNING: The iron gives off steam continuously only if you hold the iron horizontally. You can stop the continuous steam by placing the iron in a vertical position or by moving the steam selector to “®”. To prevent water dripping steam function available at the highest temperatures only. NOTE: To prevent water leakage from the soleplate, do not keep the powerful steam button pressed for more than 5 seconds. VERTICAL STEAM • Ensure that there is enough water in the water tank. • Stand the steam iron on its heel rest on an iron-safe surface and plug it. • Set the temperature control dial and variable steam control to their maximum positions. • Hold the iron vertically and press the steam burst button, an intense steam will be ejected from the soleplate. WHEN YOU FINISHED IRONING • Set the temperature dial to the minimum position. • Remove the mains plug from the wall socket. • Stand the iron on heel rest. CARE AND CLEANING • Before cleaning the steam iron ensure it is unplugged from the power supply and has completely cooled down. • Do not use abrasive cleaners. SELF-CLEANING • Fill water reservoir up to the maximum level and then close it. • Set the temperature control to its maximum position. • Insert the main plug into the wall socket. • Allow the iron to heat up until the indicator light goes out. • Holding the iron horizontally over the sink then change the steam control to the self-cleaning position and press the self-cleaning button. • Boiling water and steam will be ejected from the holes in soleplate with Impurities washed out. Rock the iron forwards and backwards during this operation. • Repeat self-cleaning if you notice that much impurity has been washed out. • Move the iron over an old (preferably) piece of cloth. This to ensure that the soleplate will be dry during storage. STORAGE • Unplug...