Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Plug the power into a 230/240V power outlet and switch “ON”. 4 NOTE: on label means:“This article cannot be ironed” (e.g. chlorofibre, acrylic, elastodiene). Label Code Kind of Textile Temperature Control Variable Steam Control (See garment instruction) (advised position) synthetic modacry polypropylene polyurethane acetate triacetate metalized cupro plyamide(nylon) polyester modal viscose(rayon) MINIMUM LINEN (maximum) DRY Min steam Max steam silk wool cotton linen Table A 5 Set the Variable Temperature Control to the required position within the steam range ( ) and wait until the Heating Indicator Light has gone out. Set the Variable Steam Control (on top of the handle of the iron) to the required setting. Max Steam Min Steam Your Kambrook Steamline Iron is now ready for steam ironing. Important: If you attempt to iron with the Variable Steam Control on and with the Variable Temperature Control set to a relatively low ironing temperature [ie. between (synthetic) and (silk)], the water will not be able to vapourise completely.This may result in water leaking from the soleplate.Therefore, ensure that the Variable Steam Control is always set to correspond with the setting on the Variable Temperature Control as shown in Table A on page 5. How to Use the Shot of Steam The Shot of Steam provides an extra burst of steam, which is ideal for removal of stubborn creases and wrinkles during STEAM or DRY ironing. Turn the Variable Temperature Control to the hottest setting (ie. cotton/ linen) and wait until the Heating Indicator Light goes out. Ensure the Variable Steam Control setting corresponds with the setting on the Variable Temperature Control. Lift the iron slightly above the surface of the fabric, press the Shot of Steam button down firmly and then release it during ironing.An intense “burst” of steam penetrates deep into the fabric. For optimum steam quality, leave an interval of at least four seconds between pressing the Shot of Steam button. Vertical Steam System The Vertical Steam System allows you to use the iron for vertical ironing.This is especially useful for getting wrinkles out of hanging clothes, curtains, wall hangings etc. Hold the iron vertically, in front of the item to be steamed and press the Shot of Steam button. WARNING: NEVER IRON CLOTHES ON THE BODY! Dry Ironing Set the Variable Steam Control to the DRY position (= closed), this shuts off the steam flow, should there be any water in the tank. Select the setting on the Variable Temperature Control most suitable for the fabric to be ironed. Once the Heating Indicator Light has gone out, commence ironing. NOTE: If dry ironing for longer than 20 minutes, the water tank should be emptied to prevent over heating of any water present. 6 MAINTAINING YOUR KAMBROOK STEAMLINE IRON After Each Use Set the Variable Steam Control to DRY Switch off the power from outlet and then disconnect cord from the power outlet. Over a sink or bucket turn the iron upside down and shake the iron to empty the water tank and then stand the iron in an upright position to allow to cool. In order to save space, after the iron has cooled, the power cord may be easily wound around the Large Resting Heel. Always store the iron (with water emptied from the tank) on its Resting Heel, NOT on the soleplate. Even the smallest amount of moisture will cause corrosion and staining of the soleplate if the iron is stored with the soleplate facing downwards. Cleaning the Exterior and Soleplate Switch off the power from outlet and then disconnect cord from the power outlet. Certain fabric finish residues may build up on the soleplate, these may be removed by cleaning with a cloth soaked in vinegar solution.Then dry with a dry cloth. DO NOT USE ABRASIVES OR SCOURING PAD TO CLEAN THE SOLEPLATE. KEEP THE SOLEPLATE SMOOTH; AVOID HARD CONTACT WITH METAL OBJECTS. DO NOT SCRATCH OR DAMAGE THE SURFACE OF THE SOLEPLATE. Wipe down the outer housing with a damp cloth and polish with a dry one. Do not use abrasive or harsh cleaners as they may damage the surface of the iron. NEVER IMMERSE THE IRON IN WATER OR ANY LIQUIDS. DO NOT PUT VINEGAR OR OTHER DESCALING AGENTS INTO THE WATER TANK. To clean steam holes - simply use a damp cloth to wipe away any build up or lint or starch from inside the steam holes. Self Cleaning Your iron will give the best ironing results and last longer if you apply the “Self Cleaning” function regularly (once or twice a month) to remove any scale or fluff. Set the Variable Steam Control to DRY. Fill the Water Tank with water using the beaker provided to make pouring easier. Place the iron on its heel. Set the Variable Temperature Control to Linen. Plug the cord into the power outlet and turn the switch on. Allow the iron to heat up until the Heating Indicator Light goes out. Switch off the power and remove cord from the power outlet. Hold the iron horizontally over the sink. Push and hold the Variable Steam Control to the (self cleaning) symbol shown on the control. Boili...
Ce manuel est également adapté pour les modèles :Fers - KI900 (230.02 kb)