Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
The spray may be used with steam or dry ironing. 1. Simply pump the spray button when spray / S// ' s/// is desired. If the spray doesn't work immediately just keep pumping till it does. ^This P'cture is N|'56°R) 2. To get a finer spray, pump the button vigorously. To get coarser spray, pump the button more slowly. For best results, use a quick, full stroke. -6- Electronic 3-Way AUTO SHUT-OFF FUNCTION (N1-552R/553R/560R/R20NR/R15NR/R16NR Only) 1. When the iron is left unmoved with its soleplate facing down or on its side for approx. 1. minute, the iron will automatically shut off power to the heater by itself. 2. When the iron is left unmoved on its heel rest for approx. 10 minutes, the iron will automatically shut off power to the heater by itself. 3. To turn the iron back on to resume ironing, simply move the iron in any way. Reheat the iron until the indicator light goes out, if you have left the iron in its auto shut off mode for 10 minutes or more. NOTE: 1. The Auto shut off system works regardless of position of the temperature selector dial, even at "OFF" position. 2. When you finish ironing, always unplug the iron. Licensed under U.S. patent No. 4,686,352 and foreign counterparts. HOW TO USE THE JET OF STEAM FEATURE The jet of steam feature gives extra steam which goes deep into the garment and is helpful for removing stubborn wrinkles. The jet of steam feature can be used only in the 11 Q 11 indication area of the temperature selector dial when steam or dry ironing (If used at lower setting, water spotting will occur because the iron is not hot enough to change water to steam). If you have not used the "Jet of Steam" feature for a long time, it is necessary to clean the inside of the iron before using this feature on any clothes to be ironed. Simply test the "Jet of Steam" feature several times away from the ironing board and clothes to be ironed. This will prevent brown spotting or water spotting on the clothes. -7- 1. Fill the iron as described in "HOW TO FILL" 2. Set the iron vertically and make sure the temperature selector dial is set to OFF. Plug the AC cord into the electrical outlet. 3. Set the temperature selector dial to the " " indication area. 4. Preheat the iron until the indicator light goes out, usually about 1-2 minutes. 5. Simply pump the jet of steam button when it is desired. But pump the jet of steam button several times before using for the first time at each ironing session. 6. Allow at least 5 seconds between uses of jet of steam to prevent water spotting. Use a press cloth if necessary. VERTICAL STEAM(NI-560R Only) To get better results when using vertical Jet of steam, hang the garment on a clothes hanger. Curtain and drapes may also be steamed once they're hung. Hold the iron away from your body close to but not touching the fabric. Pull the fabric tight with your free hand and pump the Vertical steam button (Jet of Steam Button) at 5-second intervals as you pass the iron over the wrinkled fablic. WARNING: Never iron clothes on the body or point your iron at anyone when steaming. Keep hands and body away from steam areas while using vertical steam feature. /This picture \ \ is NI-560R/ SELF-CLEANING With the self-cleaning feature you can flush out mineral residues from the steam generating chamber and the steam vents - refreshing your iron each time for a longer steaming life. It is very important to operate the self-cleaning feature after each steam ironing to prevent mineral accumulations from hardening. 1. Check water level. Water jeygl should be at the 1/2 full. When water level is below 1/2 full, with water according to the instructions in "How to Fill". 2. Preheat at "6" setting, (in about 1-2 minutes) Make sure that the steam button is in the Dry position. 3. Set the dial to off and remove the AC plug. 4. Hold the iron horizontally over the sink. 5. Pump the "Jet of Steam" button quickly (at least 3 times per second) about 20-30 times. 6. While self-cleaning, pitch the iron up and down slowly to help clean the entire inside and let the water drip out of the sole plate vents. -8- 7. Check that all water and steam thoroughly stop coming out of the sole plate vents. After self-cleaning is finished dump any remaining water out of the iron. 8. Iron on a towel to remove any drops of water remaining on the bottom of iron. 9. Cool as usual and store the iron on its heel rest. Never store an iron on its soleplate or with water in it. NOTE: If water still remains inside the sole plate after self-cleaning operation, then dry out the iron by vaporizing the remaining water setting the iron on the "6" setting. And follow the instructions under "AFTER EACH USE". HOW TO CARE FOR YOUR IRON AFTER EACH USE 1. Turn iron off and unplug. 2. Empty iron immediately after using. Don't store the iron with water in it. 3. Depress the steam button down into the dry position. 4. Wait until the iron has cooled before storing it, and always s...
Ce manuel est également adapté pour les modèles :Fers - NI-350S (398.69 kb)