Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
-Do not connect the appliance to a wall socket intended for shavers. -Do not use the iron in your hotel room simultaneously with another high-wattage appliance (e.g. a hairdr yer) to avoid blowing the fuse. -Check the mains cord regularly for possible damage. -Always place and use the iron on a stable, level and horizontal surface. -The soleplate of the iron can become extremely hot and may cause burns if touched. -When you have finished ironing, when you clean the appliance, when you fill or empty the water tank and also when you leave the iron even for a shor t while: set the steam control to position O, put the iron on its heel and remove the mains plug from the wall socket. -The appliance is not intended for regular use. Electromagnetic fields (EMF) This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. 1 2 Before first use Remove any sticker or protective foil from the soleplate. Let the iron heat up to maximum temperature and pass the iron over a piece of damp cloth for several minutes to remove any residues from the soleplate. Preparing for use Filling the water tank 1 2 3 Make sure the appliance is unplugged and the steam control is set to position O (no steam). Open the cap of the filling opening (Fig. 2). Fill the water tank with tap water up to the maximum level. (Fig. 3) If the tap water is very hard, we advise you to use distilled water. Do not fill the water tank beyond the MAX indication. Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank. 4 Close the cap of the filling opening (‘click’) (Fig. 4). Setting the temperature 1 Check the laundry care label for the required ironing temperature. -1 Synthetic fabrics (e.g. acr ylic, nylon, polyamide, polyester) -1 Silk -2Wool -3 Cotton, linen Set the temperature control to the required ironing temperature (Fig. 5). Place the iron on its heel (Fig. 6). Put the mains plug in an earthed wall socket. 2 3 4 The temperature-ready light goes on to indicate ,5 that the iron is heating up (Fig. 7). When the temperature-ready light has gone out, wait a while before you start ironing. Tips -If the ar ticle consists of various kinds of fibres, always select the temperature required by the most delicate fibre, i.e. the lowest temperature. If, for example, the fabric consists of 60% polyester and 40% cotton, it has to be ironed at the temperature indicated for polyester ( 1). -If you do not know what kind or kinds of fabric an ar ticle is made of, determine the right ironing temperature by ironing a par t that is not visible when you wear or use the ar ticle. -Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches. -Fabrics that tend to acquire shiny patches should be ironed in one direction only (along with the nap) while applying very little pressure. -Star t ironing the ar ticles that require the lowest ironing temperature, i.e. those made of synthetic materials. Using the appliance Note:The iron may give off some smoke when you use it for the first time.This stops after a short while. Steam ironing 1 2 Make sure that there is enough water in the water tank (see chapter ‘Preparing for use’, section ‘Filling the water tank’). Set the required ironing temperature (see chapter ‘Preparing for use’, section ‘Setting the temperature’) (Fig. 5). Steam ironing is only possible at temperature setting 3. 3 Set the steam control to position \. (Fig. 8) The iron starts to produce steam as soon as , it reaches the set temperature. Ironing without steam 1 2 Set the required ironing temperature (see chapter ‘Preparing for use’, section ‘Setting the temperature’) (Fig. 5). Set the steam control to position O (no steam) (Fig. 9). Steam boost The steam boost provides extra steam to remove ver y stubborn creases. 1 2 Make sure that there is enough water in the water tank. Set the required ironing temperature (see chapter ‘Preparing for use’, section ‘Setting the temperature’) (Fig. 5). The steam boost function can only be used at temperature setting 3. 3 Press and release the steam boost button (Fig. 10). Ironing without ironing board -When you are travelling, an ironing board is often not at hand. In this case, use a cotton towel on a firm flat surface. (Fig. 11) Make sure that the surface is heat-resistant and moisture- resistant. Do not use a glass or plastic surface. Cleaning 1 2 3 Place the iron on its heel. Remove the mains plug from the wall socket and let the iron cool down for at least 30 minutes. Clean the appliance with a damp cloth. To keep the soleplate smooth, avoid hard contact with metal objects. Never use a scouring pad, vinegar or other chemicals to clean the soleplate. Storage 1 2 3 4 Set the steam control to position O (no steam). Place the iron on its heel. Remove the mains plug ...