Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. SAVE THESE INSTRUCTIONS. 7 Soft-Touch Parts Note: The soft-touch parts They are safe for individuals or sensitive to these POLARIZED PLUG (120V Models Only) This appliance has a polarized reduce the risk of electric shock, this plug If the plug does not fit fully into the contact a qualified electrician. Do not TAMPER-RESISTANT SCREW Warning : This appliance is equipped with a tamper-resistant screw to prevent removal of the outer cover. To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized service personnel NOTE: If the power supply cord is damaged, it must manufacturer or its service agent or a similarly qualified to avoid a hazard. 8 AS385Pub10000001628 4/4/2:40 Page Product may vary 1. Spray nozzle 2. Water-fill cover 3. Dry/Steam selector and self-cleaning selector 4. Spray button 5. Surge-of-steam button 6. Handle 7. Pivoting cord 8. Fabric guide 9. Heel rest 10. Temperature-ready indicator light 11. Fabric-select dial 12. Water tank 13. Soleplate 9 Auto cleaning Dry Steam/Blast of Steam Spray Symbols How to Use This appliance is for GETTING STARTED Remove any labels, stickers Important: For warranty verification, Note: Use ordinary tap water for ironing. home softening system. Important: For optimum performance, let the iron beginning to iron. TO FILL THE WATER TANK A C D E B 1. Grasp the water-fill cover and pull it out to expose the water-fill hole. Be careful not to pull too hard as the water-fill cover is attached to the inside of the water-fill hole (A). 2. Tilt the iron and using a clean measuring cup, pour water into opening until the water reaches the MAX level mark on the water tank (B). Do not overfill. 3. After filling, be sure to push the water-fill cover securely back into the water-fill hole. 4. Plug in the iron. The power on indicator light comes on (C). Tip: If unsure of a garment’s fiber, test a small area (on an inside seam or hem) before ironing. FOR STEAM IRONING 1. Turn the selector to the desired steam level. To get maximum steam, set the selector the middle position (D). Steam is produced as soon as you hold the iron. Important: Do not set the selector past the middle position. If you do, it activates the self-cleaning feature. 2. Turn the fabric-select dial to appropriate setting (between 4 and 6) for your fabric (E). See fabric guide on the heel rest and read garment’s label to help you determine fabric type. • The temperature-ready light glows until it reaches the appropriate temperature. • It then glows on and off during ironing. This is normal. 3. When finished ironing, turn the fabric-select dial to lowest heat setting, move the selector to and unplug the iron. FOR DRY IRONING 1. Make sure selector is set to . You may want to empty the water (see “Emptying Water Tank After Ironing - Optional”). 2. Turn the fabric-select dial to the appropriate setting for your fabric. See fabric guide on the heel rest and read garment’s label to help you determine fabric type. 10 11 12 SURGE OF STEAM • Horizontal 1. With the water tank filled to the MAX mark, turn the fabric-select dial to at least setting 4 and wait for the temperature-ready light to go off. 2. To remove tough wrinkles, pump the button a few times at 5-second intervals for a concentrated blast of steam. • Vertical 1. Hang the garment to be steamed on a clothes hanger. (Curtains or drapes can be steamed once they are hung.) 2. Set the steam selector to the middle position. 3. Hold the iron close to, but not touching, the fabric. 4. Pull the fabric tight in your free hand and pump the button as you move the iron over the fabric (F). SPRAY You can use spray at any setting. 1. Pull out the water-fill cover. 2. Fill water tank up the MAX mark. 3. Press the button to spray water as you iron. 4. If spray is weak, pump the button a few times. EMPTYING WATER TANK AFTER IRONING (OPTIONAL) 1. Turn the fabric-select dial to . Unplug the iron and let it cool. 2. Pull out the water-fill cover to expose water hole. 3. Empty the water by holding the iron over a sink with the tip pointing down. Water will empty out of water-fill opening (G). Care and Cleaning This product contains no user serviceable parts. Refer service to qualified service personnel. CLEANING OUTSIDE SURFACES 1. Make sure iron is unplugged and has cooled completely. Wipe the soleplate and outer surfaces with a soft cloth dampened with water add mild household detergent. Never use abrasives, heavy-duty cleansers, vinegar or scouring pads that may scratch or discolor the iron. 2. After cleaning, steam iron over an old cloth to remove any residue from the steam vents. SELF-CLEANING To keep the steam vents free of any buildup, about once a month follow these instructions. 1. Fill the water tank well below the MAX line. 2. ...