Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
This does not indicate that the boiler is really empty, it is simply part of the normal heating process. 7. This appliance has a water level sensor. The «Refill boiler» indicator (6) will light when the boiler is empty. Refilling the boiler Attention! Risk of burns! Be careful when opening the cap, steam may escape. If the pilot lamp (6) illuminates : 1. Press the steam button (12) to check that no more steam is generated. Only then the boiler should be refilled. 2. Set the appliance switches (7 & 8) to the off position («0») and unplug the steam station from the mains. Then wait for minimal 2 minutes. 3. Open the cap (1) carefully and slowly. Allow remaining steam to escape. 4. Refill the boiler using always the funnel. Do not overfill the boiler. 5. Close the cap firmly. Important: • Normal tap water can be used. To prolong the optimum steam function, mix tap water with distilled water 1:1. If the tap water in your district is very hard, mix tap water with distilled water 1:2. You can inquire about the water hardness with your local water supplier. • To avoid damage and/or contamination of the boiler, do not put perfume, vinegar, starch, descaling agents, additives or any other type of chemical product into the boiler, unless they have been advised by Ufesa. • During it first use the iron may produce certain vapours and odours, along with white particles on the soleplate, this is normal and it will stop after a few minutes. Setting the temperature 1. Check the ironing instruction label on the garment to determine the correct ironing temperature. 2. Select the temperature (11): «•» Synthetics «••» Silk – Wool «•••» Cotton – Linen 3. The indicator lamp (13) will remain lit while the iron is heating and go out as soon as the iron has reached the selected temperature. Tips: • Sort your garments out based on their cleaning symbol labels, always starting with clothes that have to be ironed at the lowest temperatures. • If you are not sure what the garment is made of then begin ironing at a low temperature and decide on the correct temperature by ironing a small section not usually seen when worn. Controlling the pressure (Depending on the model) Your steam station is equipped with a pressure gauge (3) which shows the pressure it works at every moment. Dial of the gauge is divided into three areas : 1) Yellow area shows low pressure (during first heating or loss of pressure during the ironing. In this case, read Trouble Shooting section). 2) Green area is the one in which the station works normally and pressure should be within it during ironing. 3) Red area shows high pressure and during normal use should not be reached. In case your steam station reaches it frequently, it will have to be checked by a technical service centre. Ironing with steam (B) 1. Turn the temperature selector (11) to the steam position, between «••» and «max». 2. Set the amount of steam to suit your needs, using the variable steam control (4) (depending on the model). 3. Press the steam release button (12) to release steam. Cork handle iron (depending on the model): To get permanent steam, press the lock button (15) and slide it backwards until it locks. To switch off the permanent steam, slide the lock button forward. Important: • The steam hose may get hot if you are ironing for long periods. Ironing without steam 1. Set the required ironing temperature. 2. Begin ironing but without pressing the steam release button (12). Vertical steam (C) 1. Set the temperature control to the «••» or «max» position. 2. You can steam iron curtains and hanging garments (jackets, suits, coats...) by holding the iron in a vertical position and pressing the steam release button (12). Operate the iron vertically at a distance of 10 to 20 cm. Never direct the steam jet at garments that are being worn. Never aim the steam at people or animals. Cleaning the Boiler To extend the life of your steam generator and to avoid any build up of scale, it is essential that you rinse out the boiler after 10 uses. If your water is hard, increase the frequency. Do not use descaling agents for rinsing out the boiler (unless they have been advised by Ufesa), as they could damage it. 1. Check that the appliance is unplugged and cold for more than 2 hours. 2. Unscrew the boiler.s cap (1). 3. Empty the boiler above a sink by holding the appliance upside down. 4. Fill the boiler with 500 ml of fresh water. 5. Shake the base unit for a few moments and then empty it completely over a sink or bucket. 6. To obtain the best result, we recommend that this operation is done twice. 7. Close the cap. Cleaning & Maintenance Important: Always unplug the appliance from the mains supply before carrying out any cleaning or maintenance operation on it. 1. After ironing, pull out the plug and allow the appliance to cool down before cleaning. 2. Wipe the housing, handle and iron body with a damp cloth. 3. If the soleplate is soiled with dirt or scale, clean it with a damp cloth. 4. Never use abr...
Ce manuel est également adapté pour les modèles :Fers - PL1420/01 (2.25 mb)