Évaluations - , GPA: ( )

Instructions Morphy Richards, Modèle SF-475

Fabricant : Morphy Richards
Taille : 329.98 kb
Nom Fichier : dfc96f16-39e3-4cac-a769-c90c9962f326.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

/ 473 ml.) with water. NOTE: To prolong the life of your Fabric Steamer, we recommend using distilled or de-mineralized water. 6. Using Water Funnel, carefully pour water from Measuring Cup into Water Reservoir through fill hole. WARNING: Extreme caution should be used when pouring water into the Water Reservoir. Do not look directly down into fill hole when filling. Keep your free hand and any children or pets at a safe distance. 7. Depending on how long you intend to steam, you may repeat steps 5 & 6 up to two more times, to a maximum of 48 oz. (1420 ml.) of water. See chart below for a comparison of the amount of water vs. approximate steam time. 8. Replace Water Reservoir cap, ensuring that it is screwed on tightly to prevent hot steam from escaping and causing injury. 9. Lower Compartment Lid back down. IMPORTANT: When steamer is first activated, it is natural for it to spray small amounts of water. This is due to condensation forming in the Hose, and will dissipate within 30 seconds of use. To help clear condensation out of Hose more quickly, try the following: • Point Steam Nozzle towards ground, sink or tub and shake it to force water out of Hose. • Extend Hose vertically as far as possible to allow water to drain back into Water Reservoir. Top Innovations, Inc. USING THE FABRIC STEAMER OPERATING THE FABRIC STEAMER NOTE: Be sure that any desired attachments are connected and Water Reservoir is filled before following these steps. 1. Plug grounded power cord into a convenient 3-prong electrical outlet. 2. Switch Lighted On/Off Switch to “On” position. 3. Steam Ready Light will illuminate while boiler is heating. When Steam Ready Light deactivates (2-8 minutes, depending on amount of water in Water Reservoir) unit will automatically begin emitting steam. 4. Place garment on a clean, rust-free clothes hanger. 5. Place hanger (with garment) on Clothes Hanger Hook (FIGURE 10). CAUTION: Use care when handling garments on the Clothes Hanger Hook. Pulling on the garment with too much force may cause the unit to tip over. 6. Direct Steam Nozzle towards bottom of garment. Steam will rise along inside and outside of fabric, removing wrinkles. Slowly slide Steam Nozzle vertically, from bottom to top of garment (FIGURE 11). NOTE: Do not allow kinks to form in hose at any time during use. 7. Direct Steam Nozzle away from garment and smooth fabric with your free hand. 8. Repeat steps 6 & 7 as necessary until fabric is smooth and wrinkle free. OTHER STEAMING TIPS • Curtains and draperies may be steamed while still hanging. • To remove wrinkles from towels, handkerchiefs and napkins, drape them over a rod or towel rack and gently steam them. • Heavier fabrics may require repeated steaming to effectively remove wrinkles. • To remove exceptionally stubborn wrinkles steam both sides of fabric. • For additional assistance in removing tough wrinkles, or to remove lint and other particles, attach Fabric Brush or Lint Remover to Steam Nozzle (see Attaching Lint Remover and Fabric Brush section on page 8 of this manual). • Use Press Pad in order to steam difficult spots and edges and to create creases in fabric. Slide your hand through the velcro strap on back of Press Pad to secure it to your hand. This will protect your hand from the flow of hot steam. Then steam fabric while pressing it firmly but gently against the Press Pad. 9. When you have completed your steaming tasks, immediately switch Lighted On/Off Switch to “Off” position and unplug power cord from electrical outlet. Refer to Proper Storage section on page 11 of this manual for information on proper cleaning and storage of Fabric Steamer. FIGURE 10 FIGURE 11 Top Innovations, Inc. CARE &STORAGE GUIDELINES PROPER STORAGE Preparing your Fabric Steamer for storage is quick and simple. When you have finished your steaming tasks, follow the steps listed below. 1. Unplug grounded power cord from electrical outlet. 2. Allow unit to cool completely (at least 30 minutes). 3. Remove all attachments from unit. 4. Drain any remaining water in Water Reservoir into a sink or tub to prevent over-filling during your next use. 5. Unhook three extension locks on Telescopic Pole, and press down on Pole Top to collapse Pole into compact storage position. Re-lock extension locks. 6. Wrap Hose loosely around Telescopic Pole one time, and hang Steam Nozzle from Steam Nozzle Holder. 7. Store all attachments safely away, preferably inside Storage Compartment or near Fabric Steamer. 8. Store Fabric Steamer in a cool, dry location. REMOVING MINERAL BUILD-UP A common problem with steam appliances is mineral build-up caused by high mineral content in many municipal water supplies. The best way to avoid this is to use de-mineralized or distilled water in unit. If you are unable to use demineralized or distilled water, we recommend you use this procedure monthly to help avoid mineral build-up: 1. Switch Lighted On/Off Switch to “Off” position and unplug grounded power cord from electrical out...