Évaluations - 5, GPA: 4.4
(
)
)
|
Facilité d'utilisation
Textiles and clothes are supposed to carry ironing instructions. If they don’t you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Filling 1 Make sure that the iron is not plugged in and then set the steam control . to the ‘ ’ position before filling the iron with water. 2 Lift up the fill cap and fill with water through the filling hole › using the beaker provided. A 11/2 beakers fills the tank (230 ml). After filling replace the fill cap. In hard water areas the use of distilled or demineralised water is recommended. Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refridgerator. 3 Always pour out the remaining water after use. WARNING: When filling your iron with tap water always use the beaker provided. Never fill directly under the tap. Temperature control Plug in the iron and switch on. Set the temperature control dial B to the temperature required, but don’t start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. Your Morphy Richards iron is fitted with an indicator light ‚ which will go on and off while you are ironing. . ¤ ‹ › fi fl ‡ · ‚ A B „ 40310 Rev 2 24/8/07 15:08 Page 4 This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. It is always a good idea to begin with cool fabrics and work up to higher settings. An iron heats up quicker than it cools down so you’ll save time and electricity. Features of your iron Temperature indicator light The indicator light shows that the iron is warming up. When the required temperature is reached the light will go out and will cycle on-off during operation. Dry ironing You can use your iron as a dry iron only. Make sure the steam control . is set to the ‘ ’ symbol. Any temperature setting may be used depending on the garment. The spray feature may be used provided there is water in the tank (see filling section). You do not need to put any water in the tank when dry ironing only. Spray Press the spray button ¤ and aim the spray of water at stubborn creases. You can do this whilst dry ironing providing there is water in the tank. When using the water spray it may be necessary to push the button a few times to get the spray pump primed. Steam control Fill the iron with water as described in ‘Filling’, page 4 and insert the plug into the electrical socket. The steam output can be switched from off to on by sliding the steam control C. . The steam facility should only be used on garments which are suitable for ironing at 2 and 3 dot setting. Shot of steam (certain models only) Press the shot of steam button ‹ to obtain a burst of extra steam for ironing out creases in heavy material such as denim etc. The shot of steam can be used whilst dry ironing, providing there is water in the tank, and the temperature control is set within the steam range. Do not use shot of steam at temperatures below the steam range shown on the control. Note: For optimum steam quality, do not operate the shot more than three times in succession. Variable steam (certain models only) Fill the iron with water as described in ‘filling’, page 4 and insert the plug into the electrical socket. The steam output can be varied from low to high by the sliding the variable steam control C. When using the iron at the bottom of the steam temperature range, the steam output should be adjusted to the lowest setting. 5 Steam No steam C 40310 Rev 2 24/8/07 15:08 Page 5 Vertical steam (certain models only) Hold the iron in a vertical position between 1cm and 2cm away from the item D. Press the shot of steam button ‹, this will create vertical steam. This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings etc. Note: For optimum steam quality, do not operate the shot more than three times in succession. Emptying and storing When you have finished ironing, unplug your iron. Ensure that the steam control is set at the ‘ ’ position, lift up the fill cap and empty any remaining water out of the filling hole. Do not store in the box, but in an upright position, so that any drops of water remaining cannot leak out and discolour the soleplate. Important: The flex can be damaged if wound too tightly around the iron after use. Make a loose loop with the flex and wrap it around the iron. The iron must be cool before winding the flex and storing on its heel. Maintenance Jet cleaning (certain models only) Your iron has a built in cleaning system designed to keep the water valve, steam chamber and steam vents clear of lint and loose mineral deposits. The ‘jet clean’ should be operated after each period of ironing. To operate, ensure that there is little water in the tank, place the iro...