Évaluations - 4, GPA: 3.8
(
)
)
|
Facilité d'utilisation
2 Fit the cord cactus into one of the cord cactus locations. Place the steam supply cord into one of the grooves on the other end of the cord cactus. This will keep the cord in an upright position. filling with water 1 Unscrew the boiler cap by turning anticlockwise. 2 Use the funnel to fill the boiler. Maximum capacity when empty is 0.9 l. Take care not to overfill if the steam station contains water. 3Refit the cap, don’t overtighten. . Filtered water is best as it reduces limescale, prolonging the life of your steam station (Kenwood water filters are widely available). Alternatively use 50% tap water and 50% distilled water. . Do not add anything else to the water such as water from clothes driers, scented water, water from refrigerators, air conditioners, batteries, bottled mineral water or rain water. These contain organic waste or mineral elements that become concentrated when heated and cause spitting, brown staining or premature wear to the steam station. refilling the boiler The red low water indicator light will glow when the boiler requires filling. NEVER UNSCREW THE BOILER CAP AS LONG AS THE BOILER IS UNDER PRESSURE. Carry out the following procedure to release the pressure: 1Press the steam button until the steam stops coming out - this may take several minutes, then release the steam button. 2Wait until the red low water indicator light comes on, then press the steam button again to release any residual steam. 3 Switch off and unplug the steam station and wait 5 minutes. 3 4 VERY SLOWLY unscrew the boiler cap. If any steam is heard, stop unscrewing the cap and wait until all the steam has gone. Once all the steam has gone continue to slowly unscrew the cap. 5 Use the funnel provided and slowly refill the boiler by pouring the water down the side of the funnel. Take care not to overfill. 6 Screw the boiler cap back on until it is completely tight. 7 Plug in the appliance. Wait for the green ready to steam light to glow, this indicates that the steam station is ready for use. important Never unscrew the boiler cap whilst the appliance is connected to the power supply and whilst there is pressure inside the boiler. Never unscrew the boiler cap during ironing. choosing the right temperature Follow the clothes label advice. Match the dots on the label to the dots on the temperature control. If there’s no label, here’s a guide on which temperature to choose: hints . Start on clothes needing the lowest temperature, then work upwards. (This lowers the risk of burning something because an iron switched from ‘hot’ to ‘cool’ takes time to cool down.) . For mixed fibres, eg cotton ... and polyester ., use the lowest suitable temperature .. . If in doubt, start with a low temperature on a part that won’t be seen (eg a shirt tail). setting the temperature Before switching on the steam station, make sure that the lock for continuous steam is in the off position by firmly pressing the lock on the left hand side of the iron. This will ensure that the steam button is released. 1 Plug the steam station into the power supply. 2 Switch on, the blue light will glow. 3Turn the temperature control to the temperature you want, the light under the control will glow. When the iron reaches the set temperature, the light will go out. (During ironing, this light will go on and off as your iron maintains the right temperature.) dry ironing Follow the procedure above for setting the temperature. Care should be taken not to press the steam button. steam ironing 1 Make sure there is water in the boiler. Plug into the power supply and switch on. 2Turn the temperature control to the desired setting. For best results when steaming we recommend that the temperature control should be set to . It is possible to vary the amount of steam produced. If the iron is set to . move the variable steam control to the left for minimum steam. If .. is selected move the variable steam control to the middle and if ... is selected move the variable control to the right for maximum steam. 3Wait until the green ready to steam light glows indicating that the correct pressure has been reached. This takes about 8 minutes. (Also wait until the temperature control indicator light has gone off.) . During ironing the light will turn on and off - this is normal and indicates steam is generated in the boiler. 4 4 Before starting to iron or if you have not used the steam function for a few minutes or if you have recently cleaned the steam station, hold the iron away from your ironing and press the steam button several times. This will enable any cold water condensed in the pipes etc., to be removed from the steam circuit. 5To produce steam whilst ironing clothes press the steam button. For continuous steam, press the steam button and then press the lock for continuous steam on the right hand side of the iron. To stop continuous steam, press the button on the left hand side. When using the steam function, the green ready to steam indicator light will go off. ....
Ce manuel est également adapté pour les modèles :Fers - IC450 (92.27 kb)