Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
(See Step "Check for gas leaks.") Note - The hardware size of nuts, bolts and screws is given. For example "1/4-20 x 2 inch bolt" means a bolt 1/4 inch in diameter with 20 threads to the inch, 2 inches long. On a small screw for example, "6-32 x 1/2 inch screw" means a number 6 screw,with 32 threads to the inch, 1/2 inch long. While we give much attention to our products, unfortunately an occasional error may occur. If a part is missing, do not go back to the store. Call the Weber Customer Service Center toll free 1-800-446-1071 to receive immediate assistance. Have your owner’s manual and serial number of the barbecue available for reference. Step 1 Check package contents Cooking box (assembly) Lid (assembly) Hose Bottom tray Cooking grates (2) Flavorizer Bars (5) Control panel ® ® ® ® ® ® ® ® 7 Left frame Front panel Right frame Catch pan holder Wheel frame Catch pan Leg frame Drip pans (2) Frame connector Thermometer Work table Wheels (2) WEBERWEBERWE BER WE BER Swing table assembly Support rod Accessory racks (2) Warming rack 8 Check contents of hardware packs Plastic buttons (2) (actual size) Burner control knobs (3) 1/4 inch nylon washers (9) Tool holders (3) Hair pin cotters (2) Tubing plugs (7) (two are spares) Wheel hubcaps (3) Support rod holder 1/4-20 keps nut Swing table end bracket Phillips screws/washers (2) Manifold bracket Hinge pins (2) (hardware size: 1/4 x 1 1/2 inch clevis pin) (actual size) 1/4-20 x 2 inch bolt (actual size) 1/4-20 x 1 3/4 inch bolts (2) (actual size) 1/4-20 x 1/2 inch bolts (6) (actual size) 9 Step 2 Assemble wheel frame You will need: wheel frame, two wheels, two wheel hubcaps, hammer and a block of wood. Set one end of wheel frame on the block of wood (or other hard, protected surface). Put one wheel on axle, WEBER side facing up, and tap on one hubcap. Figure 1. Repeat with other wheel and hubcap. Figure 1 WEBER WE BER Step 3 Assemble top frame You will need: left frame, right frame, two 1/4-20 x 1/2 inch bolts, two nylon washers and a 7/16 inch wrench. Note - Work on carpeted area (on grass or one of the boxes) to protect the finish during frame assembly. Lay the leg pieces as shown so the leg tabs point up. Figure 2. Slip the two frame pieces together with the tabs inside. Figure 2 (a). Slip washers on bolts, insert bolts as shown and tighten. Figure 2 (b). (If you try to insert a bolt and there are no holes, you have the left frame turned the wrong way. Turn the left frame around.) Frame tabs Figure 2 Leg tabs (a) (b) Right frame Left frame 10 Step 4 Continue frame assembly You will need: leg frame, wheel frame, four 1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16 inch wrench. Place the leg frame onto the tabs of the left frame with the dimple to the inside. Figure 3. Place the wheel frame onto the tabs of the right frame with the dimple to the inside. Figure 3. The leg tabs must be on the inside of the frames. Add the washers to the bolts, insert in the holes as shown and tighten with the wrench. Figure 3. Dimples to the inside Figure 3 Step 5 Install tubing plugs You will need: two tubing plugs and a hammer. Insert tubing plugs into the ends of the leg frame. Figure 4. To fully seat the plugs, you may have to tap them lightly with a hammer. Step 6 Add front panel You will need: front panel and two plastic buttons. Turn frame assembly right side up. Align the panel with the holes in the frame and insert the plastic buttons through the front panel and frame. Figure 5. Plastic buttons View from rear of barbecue Figure 5 Figure 4 11 Step 7 Add cooking box You will need: frame assembly, cooking box assembly, 1/4-20 keps nut, 1/4-20 x 2 inch bolt, pliers and a 7/16 inch wrench. Set the cooking box in the frame so the burner tubes are under the frame brace. Figure 6. Burner tubes Frame brace Figure 6 Slide the cooking box to the left within the frame. Put washer on bolt. Insert the bolt through the frame and cooking box with the head of the bolt outside the frame. Figure 7. Add the keps nut. Tighten by holding the bolt with pliers while you tighten the nut with a wrench. Figure 7 Your Weber Gas Barbecue burner assembly has been factory assembled, pressure and flame tested. As a safety precaution we recommend you check the burner alignment: a) Do the valves fit into the ends of the burners? Figure 8 (a). b) Are the ends of the burners under the washers at the left rear and left front of the cooking box? The screws are only guides. Do not tighten. Figure 8 (b). c) Are the wing nuts under the burner assembly hand tight? Do not tighten with pliers. Figure 8 (c). If you answered YES to a, b and c, the burners are correctly aligned. If you answered NO, the burners are misaligned. Contact Weber-Stephen Customer Service. Do not use barbecue. Guide screw (a)(b) (c) Wing nuts View from behind cooking box Figure 8 12 Step 8 Install manifold bracket You will need: manifold bracket Hook the bracket onto the manifold at the center burner valve. Figure 9. Place your hand unde...