Évaluations - 4, GPA: 3.8
(
)
)
|
Facilité d'utilisation
10. Never use or rest iron on an unstable surface. 11. While the iron is hot, never set iron on an unprotected surface - even if it is on its heel rest. 12. CAUTION! TO PREVENT ELECTRIC SHOCK OR OTHER INJURY, before filling the iron with water, make sure that the plug is removed from the outlet. SPECIAL INSTRUCTIONS1. To avoid a circuit overload, do not operate another high- wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, use a 15-ampere cord. Cords rated for less amperage may overheat. Use care to arrange the cord so that it cannot be pulled or tripped over. 13. WARNING: Never fill the iron with fabric conditioner, starches or any other solution, as these will damage the steam mechanism. Do not use contaminated water. 14. CAUTION! TO AVOID FIRE, never leave iron unattended while it is plugged in. 15. CAUTION! TO PREVENT ELECTRIC SHOCK, never use the iron in a location where it can fall or be pulled into water or another liquid. If the iron falls into water or other liquid, unplug it immediately. DO NOT reach into the water or liquid. 16. WARNING: Never use scouring pads, abrasive or chemical cleaners, or solvents to clean the exterior or soleplate of your iron. Doing so will scratch and/ or damage the surface. 17. CAUTION! DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur. 18. Always store your iron standing upright, not on the soleplate. If stored face down, even the smallest amount of moisture will cause the soleplate to corrode and stain. 19. This appliance is for household use only. PROBLEMPOSSIBLE REASONS & SOLUTIONSIron does not heatSome odor or small particles come out of steam vents of new ironIron does not steamWater droplets comingfrom steam vents• Iron should be plugged into a 120V AC electrical outlet only. Make sure that the plug is securely in the socket. • Temperature setting too low. Turn to higher setting. • This is normal. Follow instructions for first use and allow iron to steam through 2- 3 fillings & press the steam burst button occasionally to eliminate small white particles. • Water tank may be empty or water level is very low. Add water. • Make sure that the fabric/temperature setting and the variable steam control are correctly set. Formaximum steam, (setting ‘Max’ on steam control), temperature setting should be set on ‘• •• ’. • Variable steam control dial is set on “0”. Always allow the iron to reach the selected temperature with the variable steam control setting at ‘0’. Make sure the temperature setting is set in the correct steam area, e.g. ‘•’, and the steam control is noton ‘0’. For more steam, turn temperature dial to higher setting, e.g. ‘••• ’, and the steam control to ‘Max’. • If temperature setting and steam control setting arecorrect and there is no steam, gentlytap the soleplate on the ironing board a few times. Movethe variable steam control from ‘0’ to ‘Max’ a fewtimes. • Iron may not be hot enough. Set thermostat to the‘Max’ position. Always allow iron sufficient time toheat up before activating the variable steam control. • Overuse of steam burst. Allow more time betweeneach burst. • Iron may have been overfilled. Turn iron off,emptywater and follow instructions for filling. • Steam performance may be low if iron requires seasoning. To season, use regular tap water for 1or 2 tanks until steam performance improves. Text Box: SAVE THESE INSTRUCTIONS SAVE THESE INSTRUCTIONSFor Household GETTING TO KNOW YOUR ELECTRONIC IRON The odor is safe and should not reoccur after initial heating. Also, before ironing with steam for the first time, allow iron to heat, hold in a horizontal position and hit the burst of steam button several times. The iron may emit some small particles from the steam holes. This is normal and wil clear after pressing the burst of steam button several times. 1. Electronic Temperature Control 2. Display Panel 3. Atomizer Spray Button 4. Burst of Steam/X-Tended Steam BurstTMButton 5. Variable Steam Control 6. Water Inlet Door 7. Spray Nozzle 8. Water Level Window 9. Stainless Steel Soleplate 10. Handle 11. Auto-Off Light 12. Power Light 13. Fabric & Steam Settings 14. Temperature Indicators 15. Extra Large Soleplate 16. Soleplate Clip 17. Soleplate retaining tabs 18. Water Flask 2 Display Panel Before using your Shark Professional Intelligent Electronic Iron, remove any labels, stickers or tags that may be attached to the body or soleplate of the iron. When turned on for the first time, your new iron may emit an odor for up to 10 minutes. This is due to the initial heating of the materials used in making the iron. Technical Specifications Voltage: 120V., 60Hz. Power: 1750 Watts 9 IRONING CHART NOTE: Always refer to the garment care tag for ironing instructions. Before starting to iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an inside seam. 98762543116171510171813141211 DIRECTIONSON LABELFABRICLED...