Évaluations - , GPA:
(
)
)
Fabricant : HoMedics
Taille : 1.24 mb
Nom Fichier : f62e95b6-0504-4ef6-acaf-c8fb54767512.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
Whenever the adapter is used, it must be held in place by a metal screw. See Figures D and E. Perfect Steam Features • Safe for use on all types of fabrics • Quick heat-up feature emits steam in 45 seconds • Convenient integrated garment hanger • Telescoping design for compact storage • 5 foot flexible hose with Safe Touch® hose cover for safe and comfortable handling • Easy-fill water tank provides 45 minutes of continuous steam • Rolling casters for excellent mobility • Low water auto shut-off for safe use Assembly Instructions 1 Carefully remove all contents from packaging and inspect the product to make sure all components have been received (Fig. 10). 2. Insert pole into top of unit. Match the grooves on the pole with the notches in the pole connector and push down. Securely tighten the nut on the pole over the connector by turning it clockwise (Fig 1). 3. To attach the hanger attachment, align tabs in hanger attachment with grooves on pole and push down (Fig. 2). 4. Fully extend the telescopic pole. To do so, open the 3 clips on the pole and pull the pole upwards (Fig. 2). When fully extended close the clips. Make sure that the pole is securely locked into place and cannot be pushed downward. 5. Attach the fabric brush to the nozzle by setting into place (Fig. 3). 6. Attach handle & hose assembly to unit. Line up the nut on the hose with the screw on the hose connector. Turn nut clockwise until it is securely tightened on the hose connector, (Fig 4). It should be tightly screwed into place. Then you may hang the steamer handle onto the hanger attachment (Fig. 3). NOTE: Do not hang the hose on the hanger attachment until after it has been connected to the base to prevent the hose from falling on you. 7. Attach the crease clamp (Fig. 5) onto the nozzle tab and gently push into place. NOTE: Do not use the crease clamp and the fabric brush at the same time Pole Turn Turn Nozzle Tab Crease Clamp Clips Hanger Attachment Grounding Pin Adapter Tab for Grounding Screw Figure A Figure B Figure D Figure C Figure E Grounded Outlet Metal Screw Fabric Brush Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 6 7 Instructions for Use 1. Remove the water tank from the unit by grasping the handle and turning upside down. Unscrew the cap from the bottom of the water tank. Hold the tank under cold running water and fill to the desired level (Fig. 6). DO NOT fill past the 45 min. fill line. When you have finished filling the tank screw the cap back on and turn over (Fig. 7). Place water tank back into unit and make sure it is sitting properly & securely in the cavity. NOTE: Only fill the water tank with cold water, DO NOT use HOT water. 2. Plug the steamer cord into a 120V AC electrical outlet. 3. Turn the On/Off switch to the On position. The switch will light to indicate that the garment steamer is on. Steam will emit in 45 seconds from the nozzle. 4. Hang the garment onto the hanger attachment (Fig 8). Steam the garment in an up/down motion starting from the top of the garment to the bottom. Always keep the hose and nozzle elevated above the water container. 5. This unit has a reset button (Fig. 10). When the unit runs out of water it will automatically shut-off to ensure safe use and the red indicator light will come on above the reset button. If you wish to continue your steaming session: • Turn On/Off switch to “Off” position and unplug the power cord • Remove and refill water tank by following Step 1 under Instructions for Use • Plug the steamer cord into a 120V AC electrical outlet. • Push the reset button on side of unit • Turn On/Off switch to “On” position 6. When you are finished with your steaming session place the On/Off switch in the Off position and remove the plug from the outlet. NOTE: Be cautious when handling until steamer has fully cooled. Figure 6 Figure 7 Figure 8 Handle Hose Hose Connector Steamer Nozzle Fabric Brush Hanger Attachment Crease Clamp Pole Clips Pole Connector Water Tank On/Off Switch Casters Indicator Light Reset Button Figure 10 8 9 Using Attachments NOTE: When installing or changing attachments, be sure the unit is off, unplugged, and no steam is being released to avoid contact with hot water. 1. Fabric Brush Helps open the fabric for greater steam penetration. - Attach the fabric brush onto the steam nozzle (Fig. 3). - Move the fabric brush in a downward motion from top to bottom gently brushing the fabric. 2. Crease Clamp Helps create a straight crease - Attach the crease clamp to the steam nozzle (Fig. 5). - Push the trigger to open the crease clamp. - Place the garment between the crease clamp and steam nozzle. - Release the trigger. - Move the crease clamp in a downward motion from top to bottom to set a crease. Cleaning and Maintenance 1. Be sure the steamer is turned off and unplugged. 2. Allow the steamer to cool for at least 30 minutes. 3. Empty any excess water from the water tank and allow it to air dry before replacing the cap and setting it back in the unit. 4. Empty excess w...