Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
• Gently brush the area to be steamed with the grain or nap of the fabric. Be sure unit is unplugged and completely cool before attaching accessories. • Remove the upholstery brush once unit is unplugged and completely cool. Remove it by pressing on the tab on top of brush while pulling it forward. Fabric brush* Be sure unit is unplugged and completely cool before attaching accessories. The fabric brush opens weave of the fabrics for better steam penetration. • Attach the fabric brush to the steam head by lining up the bottom of the brush with the bottom of the steam head. Gently push the top of the brush into place on the steam head until it clicks into place. • Gently brush the area to be steamed with the grain or nap of the fabric. •Remove the fabric brush once unit is unplugged and completely cool by pressing on the release tab on top of brush while pulling it forward. *depending on model: this is either equipment specific to certain models or available as an optional accessory. 6 Crease attachment* Be sure unit is unplugged and completely cool before attaching accessories. The crease attachment is used to make pant creases easily or to remove stubborn wrinkles. • Fasten the crease attachment to the steamer by sliding onto the steam head so it fits over the raised channels. • Gently push into place. • Push on the handle to open the crease attachment. • Put your fabric in the space between the crease attachment and the head of the steam brush. • Release the handle. • Move the crease attachment in a downwards motion starting from the top. • Once unit is unplugged and completely cool, remove the crease attachment by sliding it off of the steam brush. Lint pad* The lint pad is a separate accessory and cannot be attached to the steam head. You can use the lint pad independently from the steamer. The lint pad removes hair, lint and animal fur for a professional finish. • To use the lint pad, slowly brush the clothing with the grain or nap of the fabric. • The pad can be cleaned by brushing in the opposite direction. We recommend cleaning on an old cloth that can be discarded. *depending on model: this is either equipment specific to certain models or available as an optional accessory. 7 After use • After using the steamer, switch the power off (power indicator light will go out) and unplug the appliance. Wind the power cord on its storage place under the appliance. • Remove the steam hose. Be careful there may be hot water remaining in the steam hose after use. Always remove the steam hose before emptying your appliance. • Empty the water container from the opening shown in diagram 9b. • Place the steam connector back into place. Wrap the hose around the steamer and insert the steam head onto its housing. The head slides over the raised channels for secure storage. • You can carry your steamer by its handle for easy portability and storage. For cord winding or transport, never turn your appliance upside down. Empty all water from the unit before storing it. Cleaning Clean the main unit with a damp cloth. To maintain maximum performance, your steamer must be descaled occasionally. The descaling intervals will depend on the water quality and the frequency of use. The unit should be descaled at least once a year or every 100 hours of use. For descaling proceed as follows: 1. Unplug the unit and fill it with 1/3 white vinegar and 2/3 water. 2. Let the appliance run for 3 minutes and do not steam any clothing with this mixture. 3. Switch the appliance off. Unplug it and allow to cool down for at least 30 minutes. 4. Empty the water over the sink. Rinse the appliance with fresh water. 5. Fill the unit with fresh water and repeat steps 2-4. 8 If after descaling you believe that there is still buildup in the appliance, repeat this operation. Use a new solution of vinegar and water each time you repeat steps 1 and 2. TROUBLESHOOTING Problems Possible causes Solutions There is no steam. The steamer is not turned on. Check that your appliance is correctly plugged in and press the illuminated on/off switch (on the front of the base). The water level is too low. Turn your appliance off and refill it to the max line on the side of the water tank. The hose is kinked. Be sure that the hose is fully unraveled. There is no more water. Unplug your steamer and refill it. There is little steam. Your steamer has a build-up of scale because it has not been rinsed out regularly. Descale the steamer and descall at least once a year or every 100 hours of use. If your water is hard, increase the frequency. The water level is too low. Turn your appliance off and refill it. There is too much water. Unplug your steamer and empty it partially. Water runs through the holes of the steambrush. There is condensation in the hose. Never use steamer in a horizontal position. Hold the hose vertically outstretched and wait for water to flow back into the steamer. The steamer takes a long time to heat. Your steamer has a build-up of scale because i...