Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
There is no need for concern. Setting the Temperature Before commencing ironing, first sort the items to be ironed according to the International Textile Care Labelling Code or by the type of fabric. Iron fabrics that require the lowest temperatures first. Work through to the fabrics requiring higher temperatures. Both the Temperature Control and most items of laundry have markings corresponding with this code (see Table A). KI400_KI460KM IB v1.indd 7 7 23/12/09 10:43 AM 8 Operating Instructions continued Stand the iron on its heel and turn the Temperature Control to MIN. Plug the power cord into a 230V or 240V power outlet and switch on. Select the temperature setting required by rotating the Temperature Control dial so that the desired setting is aligned with the Temperature Indicator. The Heating Indicator light will illuminate while the iron heats to the selected temperature. Once the light has switched off, the iron has reached the set temperature and is ready for use. The light will cycle on and off during use as the iron maintains the temperature selected on the Temperature Control. CAuTION: The iron incorporates a thermal safety fuse to protect the iron from over heating. However the iron should not be left unattended while it is connected to the power outlet. Special care should always be taken when there are children in the home/ vicinity of the iron. Steam Ironing When filling the iron with water, ensure that the iron is unplugged. Set the Steam Control to the MIN position and holding the iron at an angle use the water cup supplied to fill the water tank. Never exceed the maximum water level as indicated (MAX) on the side of the water tank. Tap water can be used in your Kambrook SpeedSteam Iron unless it is particularly hard, in which case it is recommended that distilled or demineralised water be used. To Operate the Steam Control As per the indications on the Temperature Control and in Table A (see section ‘Setting the Temperature’) steam ironing is only possible at higher ironing temperatures, indicated with Cotton/ Linen on the Temperature Control. Plug the power into a 230V or 240V power outlet and switch the power on. Set the Temperature Control to the required position within the steam range and wait until the Heating Indicator Light has gone out. Set the Steam Control (on top of the handle) to the required setting. Your Kambrook iron is now ready for use. IMpORTANT: If the iron is set to a low temperature on the Temperature Control (i.e. synthetic or silk) and also on any of the steam control settings, there may be leakage from the soleplate. This is due to the iron temperature not being high enough to vaporise the water and create steam. Therefore, ensure that the steam control is always set to correspond with the setting on the temperature control as seen in Table A (see section ‘Setting the Temperature ). KI400_KI460KM IB v1.indd 8 23/12/09 10:43 AM CAuTION: The iron incorporates a thermal safety fuse to protect the iron from over heating. However the iron should not be left unattended while it is connected to the power outlet. Special care should always be taken when there are children in the home/ vicinity of the iron. Steam Ironing When filling the iron with water, ensure that the iron is unplugged. Set the Steam Control to the MIN position and holding the iron at an angle use the water cup supplied to fill the water tank. Never exceed the maximum water level as indicated (MAX) on the side of the water tank. Tap water can be used in your Kambrook SpeedSteam Iron unless it is particularly hard, in which case it is recommended that distilled or demineralised water be used. To Operate the Steam Control As per the indications on the Temperature Control and in Table A (see section ‘Setting the Temperature’) steam ironing is only possible at higher ironing temperatures, indicated with Cotton/ Linen on the Temperature Control. Plug the power into a 230V or 240V power outlet and switch the power on. Set the Temperature Control to the required position within the steam range and wait until the Heating Indicator Light has gone out. Set the Steam Control (on top of the handle) to the required setting. Your Kambrook iron is now ready for use. IMpORTANT: If the iron is set to a low temperature on the Temperature Control (i.e. synthetic or silk) and also on any of the steam control settings, there may be leakage from the soleplate. This is due to the iron temperature not being high enough to vaporise the water and create steam. Therefore, ensure that the steam control is always set to correspond with the setting on the temperature control as seen in Table A (see section ‘Setting the Temperature ). KI400_KI460KM IB v1.indd 8 23/12/09 10:43 AM 9 How To Use Shot Of Steam The shot of steam provides an extra burst of steam which is ideal for the removal of stubborn creases and wrinkles during STEAM or DRY ironing. Turn the Temperature Control to the hottest setting and wait until the heating indicator...
Ce manuel est également adapté pour les modèles :Fers - KI460KM (456.1 kb)