Évaluations - 4, GPA: 3.8
(
)
)
|
Facilité d'utilisation
If the plug should still fail to fit, contact a qualified electrician to replace the obsolete outlet. Do not attempt to defeat the safety purpose of the polarized plug by modifying the plug in any way. Use the iron on an ironing board. Ironing on any other surface may damage that surface. Do not operate the iron with the Quick Storage Shield attached. 840077000 Ev03 11/9/00 10:26AM Page 3 Before First Use • Steam vents should be cleaned before first use. Prepare iron for steam ironing, then iron over an old cloth for a few minutes while letting the iron steam. This will clean the vents. • Many irons spit or sputter during the first few uses with tap water. This happens as the steam chamber becomes conditioned. This will stop after a few uses. • During first use of the iron, it may appear to smoke. This will stop and does not indicate a defect or hazard. Know Your Iron Parts and Features 6 Automatic Shutoff Reset Button and Light 2 Spray/Blast 3 Adjustable Steam Switch 4 Water Tank Opening 5 Spray Nozzle Water Window 7 Temperature Control Dial Soleplate Power On Light Heel Rest Cord 10 11 12 Quick Storage Shield 3 840077000 Ev03 11/9/00 10:26AM Page 4 Q- Using Your Iron To Dry Iron 1. Plug iron into outlet. 2. Set the Adjustable Steam Switch 3. Turn Temperature Control Dial to desired temperature. Allow two minutes for iron to reach desired temperature. 4. To turn iron Off, turn Temperature Control Dial to Off and unplug iron. To Steam Iron 1. Unplug iron. Using a cup, slowly pour 6 ounces (% cup) of tap water into water tank opening. Do not fill iron direcdy from the faucet. 2. Plug iron into oudet. 3. Turn the Temperature Control Dial to desired fabric setting in the steam range. Set the Adjustable Steam Switch to the recommended steam level. See “Fabric Setting Chart” on page 5. 4. Allow two minutes for the iron to reach desired temperature. 5. To turn iron off, set Adjustable Steam Switch to 0 (Dry Iron). Turn the Temperature Control Dial to Off. Unplug iron. 6. Empty water from the iron following directions in “Caring for Your Iron.” Water Please use ordinary tap water. If you have extremely hard water, alternate between tap water and distilled water for use in the iron. 4 e 840077000 Ev03 11/9/00 10:26AM Page 5 Fabric Setting Chart Steam Setting Temperature Setting Off Nylon, Acrylic Silk Ironing Instructions Diy iron using spray if necessary. Dry iron on the wrong sick' of the fabric. Wool Polyester Rayon Cotton, Linen Use a press cloth and steam iron on the wrong side of fabric. lion while fabric is still damp. Iron using spray if necessary. For cotton, iron while still damp or use spray. For linen, iron fabric on wrong side. Optional Features (on selected models) Adjustable Steam Switch - This switch provides minimum steam for wool or maximum ^ steam for linen. Set the switch to 0 to change to Dry Iron. Automatic Shutoff Reset Button and Light - The light comes on when the iron is first plugged in. After one hour, the iron will shut off and the light will go out. Push the Reset Button to turn iron back on. Spray and Blast of Steam Buttons - Push Blast Button for an extra blast of steam. Push Spray Button to release a fine spray of water for difficult wrinkles in cotton or linen. Power On Light-This light comes on when the iron is plugged in and remains on until the iron is unplugged. The light stays on even if Temperature Control Dial is turned to Off. 5 840077000 Ev03 11/9/00 10:26 AM Page 6 & (continued) Quick Storage Shield - There is no need CAUTION: The soleplate may be hot, so to wait for the iron care must be used in placing the Quick to cool before Storage Shield on the soleplate. storing. Make sure the iron has been turned off and unplugged. Then, place the Quick Storage Shield on the iron immediately after ironing. Caring for Your Iron 1. The water tank of your iron should be emptied after each use. Turn Temperature Control Dial to Off. Unplug the iron and hold over a sink. Slowly tilt pointed end of iron down over sink. Water will run out of water tank opening. 2. After iron has completely cooled, wrap cord loosely around the iron and store in an upright position. Do not store iron laying flat on soleplate. Soleplate 1. Never iron over zippers, pins, metal rivets, or snaps, as these may scratch the soleplate. 2. To clean occasional build-up on the soleplate, wipe with a sudsy cloth. Do not use abrasive cleansers or metal scouring pads. 3. Always store iron upright in the heel rest position. 840077000 Ev03 11/9/00 10:26 AM Page 7 PROBLEM Iron won’t heat. Water is leaking out of the iron. Iron won’t steam. Iron leaves spots on clothing. Wrinkles not removed. Iron too hot. Cord is twisted. Things TO CHECK • Is the iron plugged in and the outlet working? Check the oudet by plugging in a lamp, • Is the Temperature Control Dial turned to a fabric setting? • If auto shutoff model, is the Reset Light il...