Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
2. Fill the water deposit through the filling hole (Fig. 1). 3. If your tap water is hard, use distilled water only. 4. Do not use chemically decalcified water. 5. The harder the water the more frequently the iron should be cleaned. 6. Throw out any excess water after use, once the iron has been unplugged. Steam Ironing 1. Fill up the iron as described in the section “How to fill the water deposit”. 2. Plug in the iron. 3. Steam ironing is only possible if you select the highest temperature***. Otherwise water may seep through the base of the iron. 4. Wait for the pilot light to go off. 5. Turn the steam regulator to the desired position 6. During pauses and when the ironing is complete, leave the iron standing upright. 7. Unplug the iron by pulling the plug out of the socket. Pour out any leftover water and let the iron cool down. Spray 1. The spray can be used when dry ironing or when steam ironing. 2. To do so, press the spray button. The spray button has to be pressed repeatedly to release the first spray. Steam blast The steam blast gives an extra steam jet to help remove tough creases. 1. Select the maximum temperature*** on the temperature gauge. Wait for the pilot light to go off. 2. Press the steam blast button. Wait a few seconds for the steam to penetrate into the fabric before pressing again. For optimum steam quality, do not apply more than three successive blasts. The spray button has to be pressed repeatedly to release the first spray. Cleaning and Maintenance Cleaning 1. Unplug the appliance before proceeding to clean. 2. Do not use solvents or abrasive products for cleaning. A damp cloth with a few drops of washing up liquid is enough. “Self-cleaning” 1. It is important to self-clean the appliance at least once a month to remove calcium and any other built-up minerals inside the iron. 2. Place the steam regulator control in the No steam position. 3. Fill up the deposit to the top. 4. Stand the iron upright and plug it in. 5. Turn the temperature gauge to the *** position. 6. Let the iron heat up until the pilot light turns off and back on again. 7. Unplug the iron and place it over the sink. 8. Press the self-cleaning button. 9. Let the water flow out through the steam vents in the base whilst lightly shaking the iron. 10. Release the self-cleaning button after a moment or when the deposit has been emptied and place the iron in an upright position. 11. Let the iron cool and then clean it. Maintenance 1. Any stains that may form on the base of the iron can be cleaned off using a cloth dampened with water and white vinegar. Problems and Solutions Should the mains connection fail, do not try to replace it since this is potentially dangerous. Take the appliance to an authorized Technical Support Service. The same applies to any other type of problem. This appliance complies with Low Voltage Directive 73/23/ EC and with Electromagnetic Compatibility Directive 89/336 EC. SAVE THESE INTRUCTIONS THIS PRODUCT IS FOR HOUSEHOLD USE ONLY! Warranty We guarantee that this product has been thoroughly inspected and tested before dispatch and is free from mechanical and electrical defects. Should defects due to faulty material or workmanship develop within two years from date of purchase, under normal domestic use, the appliance will be repaired free of charge. Note: If this product is used commercially the guarantee is limited to 90 days. Kindly retain your purchase slip for this must be presented if making a claim under the terms of the guarantee. If such proof is not available the product shall be deemed to be older than one year and a charge for service and \ or spares will be applicable. Should your appliance require attention or appear not to be operating properly, please take it to the retailer from whom it was purchased, together with all parts and your purchase slip. This guarantee does not cover wear and tear or damaged cause by over-loading negligence, accidental or improper use. Any changes will invalidate the guarantee, as would any attempted repair. SERVICE Before returning your product for service or repair – check the following: • Your household mains supply socket is working properly. • The mains supply circuit is not overloaded. • The instructions for use have been followed carefully. If service becomes necessary within the guarantee period the appliance should be returned to the retail outlet where purchased or carefully packed and marked “fragile-handle with care“ and sent carriage paid to the address below. (Postage is not refundable) Service outside the guarantee period is still available but this will be chargeable. TROUBLE SHOOTING Pre-caution Check fabric type is suitable for high steam temperature Switch steam setting to 0 (off) after use or when filling tank. Fill to MAX mark only. If iron is left on the item in the horizontal position for too long it may burn the fabric. Check temperature setting is suitable for fabric type. Ensure iron is in the upright position. Appliance must ...