Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
If the bottom of your canner is not flat, the surface unit can overheat, triggering the temperature limiter to cycle the unit off for a time. This will stop the boil or reduce the pressure in the canner. The Temperature Limiter may cycle the units off for a time if: • The pan boils dry. • The pan bottom is not flat. • The pan is off center. • There is no pan on the unit. Care and Cleaning Halogen/Radiant Cooktop Proper care and cleaning are important so your halogen/radiant cooktop will give you efficient and satisfactory service. If soil, mineral deposits from evaporated water spills or metal rub-off from aluminum cookware is not removed, it will burn on the glass cooktop surface and cause permanent discoloration. Follow these directions carefully in caring for your cooktop to assure safe and proper maintenance. Be sure that the surface unit control knobs are turned off and that the entire cooktop is cool before cleaning. Do not use a cooktop cleaner on a hot cooktop. The fumes can be hazardous to your health and can chemically attack the glass surface. Control knobs The control knobs may be removed for easier cleaning. Before removing the knobs for cleaning, please note that the knobs are in the proper OFF position. When replacing the knobs, check the OFF position to insure proper placement. The knob stem has a groove in each side. The groove on one side has a spring clip. The other groove is clear. Check the inside of the knob and find the molded rib. Wash the knobs in soap and water or a vinegar and hot water solution but do not soak. Replace the knob by fitting the molded rib inside the knob into the clear groove on the stem. Spring clip Molded rib Clear groove in stem Cooktop Use the same cleaning methods as those described for the glass ceramic top with the frame exception of using a scraper. Do not scrape the frame as this will damage the metal surface. Glass Cooktop Cleaning Halogen/Radiant Cooktop General information Clean the glass surface with cleaning cream before you use the cooktop for the first time. Also, clean the glass surface after each use. This helps protect the top and makes clean-up easier. To clean the cooktop seal around the edge of the glass, let a wet cloth rest on it for a few minutes, then wipe clean. Use a mild detergent if needed. Do not use a knife or any sharp object on the seal because it will cut or damage it. Normal cleaning Use only a recommended cleaning cream, such as Cerama Brite or another cooktop cleaning cream, on the glass cooktop. To maintain and protect the surface of your new glass cooktop follow these steps. 1. Before you use the cooktop for the first time, clean it with cleaning cream. This helps protect the top and makes clean-up easier. 2. Clean the surface with the cleaning cream after each use. 3. Rub a few drops (less is better) of the cleaning cream onto soiled area using a damp paper towel. Buff with a dry paper towel until all soil and cream are removed. Heavy, burned on soil 1. Allow the cooktop to cool. 2. Apply a few drops of the cleaning cream to the (cool) soiled area. 3. Using a damp paper towel, rub the cream into the burned-on area. As with any burned- on spill, this may require some effort. 4. Carefully scrape soil with razor scraper. Hold scraper at a 30° angle against the glass cooktop. Be sure to use a new sharp razor scraper. Do not use a dull or nicked blade. 5. If any soil remains, repeat the steps listed above. For additional protection, after all soil has been removed, polish the entire surface with the cleaning cream. 6. Buff with a dry paper towel. To order more cream and/or scrapers for cleaning your glass cooktop, please call our toll-free number: National Parts Center 800-626-2002 Cleaner # WX10X300 Scraper # WX5X1614 Cream & scraper kit # WB64X5027 Glass Cooktop Cleaning Halogen/Radiant Cooktop Special care Be sure to use a new sharp razor scraper. Do not use a dull or nicked blade. Sugary spillovers (such as jellies, fudge, candy syrups) or melted plastics can cause pitting of the surface of your cooktop (not covered by the warranty) unless the spill is removed while still hot. Special care should be taken when removing hot substances. 1. Turn off all surface units affected by the spillover. Remove hot pans. 2. Wearing an oven mitt, hold the razor scraper at a 30° angle to the cooktop. Scrape the hot spill to a cool area outside the surface unit. 3. With the spill in a cool area, use a dry paper towel to remove any excess. Any spillover remaining should be left until the surface of the cooktop has cooled. Do not continue to use the soiled surface unit until all of the spillover has been removed. Follow the steps under Heavy Burned-On Soil to continue the cleaning process. NOTE: If pots with a thin overlay of aluminum, copper or enamel are allowed to boil dry, the overlay may bond with the glass cooktop and leave a black discoloration. This should be removed immediately before heating again or the discoloration may be permanent...