Évaluations - 4, GPA: 4.3 ( )

Fabricant : DCS Taille : 464.24 kb Nom Fichier : 202392DE.pdf Langue d'enseignement:

cooking zone has been trig- Switch the cooking zone on gered again Automatic switch-off has Switch appliance off. Switch been triggered appliance on again and number are displayed Electronics fault Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house’s wiring system) If after switching on again, is displayed again, call the customer service department If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force Centre. 1 Warning! Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs. 3 If the appliance has been operated incorrectly, the engineer's visit will be chargeable, even during the warranty period. Operating noises Depending on the material and the processing of the base, the following noises may occur when using induction cooking zones. • Cracking noise (1) when using cookware made of different materials (Sandwich construction) • Whistling (1) when using an individual cooking zone or several cooking zones with high powers when the cookware is made of different materials (Sandwich construction) • Humming (2) can occur at high power levels • Clicking (2) during electric switching processes • Hissing, buzzing (3) The device is fitted with a fan for cooling the electrics. A whiring noise can be heard when operating the fan which may deviate depending on the performance and may continue for a while after the appliance is switched off. The noises described are normal and do not refer to any defects. Disposal 41 3 2 1 Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. 2 Old appliance The symbol W on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. 42 42 Installation Instructions Installation Instructions 1 Safety instructions Warning! This must be read! The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.) Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed. Anti-shock protection must be provided by the installation, for example drawers may only be installed with a protective floor directly underneath the appliance. The cut surfaces of the worktop are to be protected against moisture using a suitable sealant. The sealant seals the appliance to the work top with no gap. Do not use silicon sealant between the appliance and the work top. When building in, protect the underside of the appliance from steam and moisture, e.g. from a dishwasher or oven. Avoid installing the appliance next to doors and under windows. Otherwise hot cookware may be knocked off the rings when doors and windows are opened. z Risk of injury from electrical current. • The electrical mains terminal is live. • Make electrical mains terminal free of voltage. • Follow connection schematic. • Observe electrical safety rules. • Ensure anti-shock protection by installing correctly. • The appliance must be connected to the electrical supply by a qualified electrician. z Risk of injury from electrical current. • Loose and inappropriate plug and socket connections can make the terminal overheat. • Have the clamping connections correctly installed by a qualified electrician. • Use strain relief clamp on cable. • In the event of single-phase or two-phase connection, the appropriate mains cable of type H05BB-F Tmax 90°C(or higher) or an equivalent type must be used. • If this appliance’s mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90°C; or higher) or an equivalent type. The latter is available from the Customer Care Department. A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm. Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors. Service 43 Service In the event of technical faul...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :