Log:
Évaluations - 4, GPA: 4 ( )

Instructions Greenway Home Products, Modèle ELECTRIC STOVE MES31CR

Fabricant : Greenway Home Products
Taille : 405.28 kb
Nom Fichier : 5a3754d8-d600-4f2b-8d11-3b0c42345925.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


The extension cord shall not be more than 20 ft (6 m) in length. WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to persons. WARNING: Do not use this stove if any part of it has been under water. Immediately call a qualified service technician to inspect the stove and replace any part of the electrical system which has been under water. SERVICE INSTRUCTIONS FOR YOUR SAFETY Service must be performed by a qualified service agency. REPLACING THE LIGHT BULBS NOTE: Light bulbs may become loose during shipment. If the flame effect is dim or does not work, please check that the light bulbs are lightly secured into their sockets. See instructions for replacing the bulbs. The MES31CR, MES31MB and the MES31BL use two (2) clear 120 Volt, 25 watt B-10, E-12 socket base light bulbs (small base, chandelier candle type bulbs). The access plate is located onthe back of the unit. For convenience, if one of the light bulbs burns out, it may be easier to replace both of the light bulbs at the same time. CAUTION: To reduce the risk of fire, use 25 watt ONLY, TYPE B-10, E-12 socket base light bulbs. 1. Turn off the power to the unit. 2. Let the stove cool if it has been operating. 3. Turn the stove so you are facing the back of the stove. 4. Look for the access plate with the gold printing on it. 5. Remove the two (2) screws holding the bulb slides. These slides allow you to pull eachbulb to the access panel opening, making it easier to change the light bulb. 6. Remove the four (4) screws holding the access plate in position. Once you have removedthe four (4) screws, remove the access plate. You can now see and access the two (2) 25 watt chandelier bulbs under the ember bed. 7. Pull the bulb slides towards you until you can easily reach the bulbs. 8. Remove each light bulb by unscrewing them out of the bases, turning them towards you. You can use one hand to hold the light socket in place, if required. 9. Install the new light bulbs by turning each light bulb into the base away from you. You can use one hand to hold the light socket in place, if required. 10. Push the bulb slides back into position. 11. Replace the access plate by pushing the plate up against the stove back, and inserting the four (4) screws. 12. Insert and tighten the 2 screws holding the bulb slides in place. 13. Turn the stove back so you are facing the front of the stove. 14. Turn the power on and enjoy the flame effect. OPERATING INSTRUCTIONS After reading these instructions confirm that all controls on the stove are in the off position. Plug the stove into a 15 amp, 120 volt outlet. All controls and switches are on the front panel of the stove located inside the right handdoor. Flame – to enjoy the flame just press the power switch to the on position. Flame Brightness control – you can adjust the intensity of the flame by moving the dial from the minimum position to the maximum position. Select the brightness that you prefer. This feature will only work if the power switch is in the on position. MIN Heat (700) – to obtain low heat just press the heat switch marked 700 to the on position. MAX Heat (1400) – to obtain high heat you must ensure the thermostat dial is in the maximum position and then press the 700w and the 1400w switches to the on position. If you move the thermostat to the minimum position this High Heat Switch will be automatically shut off. CLEANING YOUR STOVE Before you clean your stove, please ensure the unit has been turned off, unplugged from the power source and theunit has cooled. To clean the doors: Remove dust with a clean, dry, soft cloth that will not scratch the surface of the door. Remove finger prints or other “oily” marks with a clean, damp, soft cloth. To clean metal, and other painted parts: Remove any marks on any of these surfaces with a clean, damp, soft cloth that will not scratch these surfaces. DO NOT USE abrasive cleansers or spray liquids on any surface of this stove. 5 6 7 8 WARRANTY DO NOT RETURN THIS PRODUCT TO THE STORE: Please contact Customer Service at: 1-866-253-0447 web: email: support@gre...

Ce manuel est également adapté pour les modèles :
Hobs - ELECTRIC STOVE MES31BL (405.28 kb)
Hobs - ELECTRIC STOVE MES31MB (405.28 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories