Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
During the first few hours of use, you may detect a smell of rubber, which will disappear quickly. 4 Installation and fastening The following instructions are intended for a qualified fitter to guide him/her along the installation, adjustment and technical maintenance procedures as correctly as possible and in full compliance with the applicable norms in force. Important : unplug the hob before all operations. Installation • This hob can be built into a worktop simply by cutting out the corresponding slot. • The worktop must be made with a material designed to withstand a temperature of approximately 100°C. • The hob should be positioned at least 40 mm (for mod:KBM 6011DH - KBM 6001 H the hob should be positioned at least 55 mm) away from the back wall or any other vertical surface in order to allow for correct ventilation and to prevent the surfaces around the appliance from overheating. • If you wish to install the hob on top of an oven, the latter must be fitted with a cooling fan. • Try to avoid installing the hob on top of a dishwasher; if this is unavoidable, place a watertight separating element between the two appliances. 10 Distance to keep between the cut-out slot and the cabinet 560 +/- 1 490 +/- 1 48 574 504 Fastening Very important: It is vital that you ensure the glass ceramic hob is built into a perfectly flat supporting surface. Deformations due to improper fastening could alter the characteristics of the hob and compromise its performance. The fastening springs are fastened by screws (see diagram). It is vital that these screws be kept accessible at all times. Insert the hob into the cut-out slot, applying pressure all along the perimeter of the hob frame so that the latter adheres fully to the worktop. REAR SPRING ASSEMBLY FRONT OF HOB KITCHEN WORKTOP 3040HOB FROM BELOW 5 Electrical connection • The electrical safety of this appliance can only be guaranteed if the latter is correctly and efficiently earthed, in compliance with regulations on electrical safety. Always ensure that this vital safety measure has been taken. If you have any doubts, call in a qualified technician to check the electrical system thoroughly. • The manufacturer denies all responsibility for damage resulting from a system which has not been earthed correctly. • Before powering the appliance, check whether the technical characteristics featured on the appliance data plate correspond with those of the mains electrical system. • Check that the current load of the mains supply and of the power sockets is suitable for the maximum power of the appliance, indicated on the appliance data plate. If in doubt, contact a qualified professional. Disconnect the appliance from the electricity supply before all operations. You may connect your hob to the electrical system in two different ways: • by means of a junction box: if the appliance is connected permanently to the mains, an omnipolar circuit breaker, accessible if necessary, with a minimum contact opening of 3 mm should be installed. • by means of a socket conforming to the regulations in force in the country where the appliance is fitted. It should be accessible whenever necessary; do not use adaptors, multiple plugs or extensions. Importan. After connecting the appliance to the flexible cable, tighten all the screws on the terminal board. Make sure jumpers are installed according to the type of mains system as indicated in the table. For example: line 1 in the table El ectri c a l c o n n ecti o n s Vo l t a g e Fr e q u e nc y Fu s e s S e c t io ns L N 1 2 3 4 5 230V-1+N~50 Hz 25 A* 2.5 mm. * Application of the simultaneity coefficient in accordance with IEC 60335-2-6 norm In the event of an incorrect connection: • if your appliance does not work, • check the position of the wires in the terminal board, • check that all screws are tight, • check the positioning of the jumpers. This appliance conforms with the following European Community Directives: -73/23/EEC of 19/02/73 (Low Voltage) and subsequent amendments; -89/336/EEC of 03/05/89 (Electromagnetic compatibility) and subsequent amendments; -93/68/EEC of 22/07/93 and subsequent amendments; Warning: If the hob is fitted above a built-in oven, the hob and the oven must be connected to the mains separately for safety reasons and to simplify operations when it is necessary to pull the oven out for some reason. 51 2 3 4 Jumper Phase Neutral Earth (brown) (blue) (green/yellow) 6 description HOBS E6014X E6011X Cooking zones Power (in W) Diameter (in mm) Power (in W) Diameter (in mm) Back left RD 750/2300 210 H 2500 230 Front left R 1200 140 R 1200 140 Back right R 1400 160 R 1400 160 Front right R 1800 180 H 700/1700 180 Overall power 6700 6800 H = halogen, R = simple radiant, RD = dual radiant Description of the cooktop and cooking zone A Cooking areas B “ON” indicator light C Control Knobs D Residual heat indicator light B Super Power 078910111221465307891011122146530789101112214653078910111221465AD3AAA 7 The different fun...
Ce manuel est également adapté pour les modèles :Hobs - E6014 (147.81 kb)