Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
_ '____ _, 2 H Hotpoint Fixing The appliance must be installed on a perfectly level supporting surface. Any deformities caused by improper fixing could affect the features and operation of the hob. The thickness of the supporting surface should be taken into account when choosing the length of the screws for the fixing hooks: • 30 mm thick: 17.5 mm screws • 40 mm thick: 7.5 mm screws Fix the hob as follows: 1. Use short flat-bottomed screws to fix the 4 alignment springs in the holes provided at the central point of each side of the hob. 2. Place the hob in the cavity, make sure it is in a central position and push down on the whole perimeter until the hob is stuck to the supporting surface. 3. For hobs with raised sides: After inserting the hob into its cavity, insert the 4 fixing hooks (each has its own pin) into the lower edges of the hob, using the long pointed screws to fix them in place, until the glass is stuck to the supporting surface. ! The screws for the alignment springs must remain accessible. ! In order to adhere to safety standards, the appliance must not come into contact with electrical parts once it has been installed. ! All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool. Electrical connection Single-phase connection The hob is equipped with a pre-connected electricity supply cable, which is designed for single-phase connection. Connect the wires in accordance with the instructions given in the following table and diagrams: GB Voltage and mains frequency 230-240V 1+N -220-240V 1+N -50/60 Hz Electrical cable Wire connection —: yellow/green; N: the two blue wires together L: brown and black together Other types of connection If the mains supply corresponds with one of the following: Voltage and mains frequency • 400V - 2+N ~ 50/60 Hz • 220-240V 3 ~ 50/60 Hz • 230-240V 3 ~ 50/60 Hz • 400V - 2+2N ~ 50/60 Hz Separate the wires and connect them in accordance with the instructions given in the following table and diagrams: Voltage and mains frequency Electrical cable Wire connection 400V - 2+N ~ 50/60 Hz 230-240V 3 ~ 220-240V 3 ~ 50/60Hz ~==r: yellow/green; N: the two blue wires together L1: black L2: brown 400V - 2+2N ~ 50/60 Hz ~==r: yellow/green; N1: blue N2: blue L1: black L2: brown ! The electrical connection for the hob and for any built-in oven must be carried out separately, both for safety purposes and to make extracting the oven easier. Terminal board On the lower part of the appliance there is a connection box for the different types of electricity supply (the picture is only an indication and is not an exact representation of the purchased model). If the mains supply corresponds with one of the following: Voltage and mains frequency • 400V 3 - N ~ 50/60 Hz proceed as follows: ! The cable provided is not suitable for the following types of installation. 1. Use a suitable supply cable, H05RR-F or higher, with the right dimensions (cable cross section: 25 mm). 2. To open the terminal board, use a screwdriver as a lever under the side tabs of the cover (see Terminal board picture). 3. Loosen the cable clamp screw and the terminal board screws in accordance with the type of UNDERSIDE OF HOB 3 connection required and position the connection supports as shown in the following table and diagrams. 4. Position the wires in accordance with the information given in the following table and diagrams and connect the appliance by tightening all the screws for the springs as much as possible. Voltage and mains frequency Electrical connections Terminal board 400V 3-N ~ 50/60 Hz i i 1 Hi ± Three-phase 400 5. Secure the power supply cable by fastening the cable clamp screw, then put the cover back on. Phase Phase Phase Three-phase 400 Earth Neutral U-bolt connection support Connecting the electricity supply cable to the mains If the appliance is being connected directly to the electricity mains an omnipolar switch must be installed with a minimum opening of 3 mm between contacts. ! The installer must ensure that the correct electrical connection has been made and that it is fully compliant with safety regulations. Before connecting the appliance to the power supply, make sure that: • The appliance is earthed and the plug is compliant with the law. • The socket can withstand the maximum power of the appliance, which is indicated on the data plate located on the appliance itself. • The voltage falls within the range of values indicated on the data plate. • The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets. ! Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible. ! The cable must not be bent or compressed. ! The cable must be checked regularly and replaced by authorised technicians...