Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
6004 - obtainable either through a local Hotpoint Service Centre or retailer). Installation • Unpacking the appliance The cooker should be carefully unpacked and checked for damage. Ensure that no packaging material Is left Inside the oven cavities. • Siting the Cooker The cooker is designed to be flush between standard kitchen units spaced a minimum 500mm apart. The clearance either side need only be sufficient to allow withdrawal of the cooker for servicing. It can be used with cabinets on one side or both, as well as In a corner setting. It can also be used freestanding. Adjacent side walls which project above the hob level should be protected by heat resistant material, but in any case should not be nearer to the cooker than 100 mm. Any overhanging surface or cooker hood should not be nearer than 650mm. • Any electrical wiring must be carried out In compliance with the appropriate IEE and electricity board regulations by a qualified electrician, eg. your local electricity board or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). • WARNINGS - INCORRECT INSTALLATION COULD AFFECT THE SAFETY OF THE APPLIANCE. - ALL APPLIANCES MUST BE EARTHED. - BEFORE CONNECTING OR INSTALLING THE COOKER THE ELECTRICITY SUPPLY MUST BE SWITCHED OFF. • IMPORTANT: The earth connection on this appliance must be made using a box spanner to avoid strain on adjacent terminals. • The installer must check that the voltage shown on the rating plate corresponds with the house electricity supply. • The cooker must be connected to a suitable double pole isolating switch (cooker control unit) having a contact separation of at least 3 mm in all poles placed In a readily accessible position adjacent to the cooker. • Access to the mains terminals is gained by removing the rear access over. • The mains cable must pass through the cable clamp adjacent to the terminal block. Sufficient cable should be used to allow the cooker to be pulled out for servicing. • The main cooker control unit must be switched ON for any part of the cooker to function. In houses fitted with a 30 milliamp RCCB, the combined use of your slot-in cooker and other domestic appliance may occasionally cause the RCCB to trip. In the unlikely event of the RCCB repeatedly tripping contact your local Hotpoint Service Office. In some Instances it may be necessary to fit a 100 milliamp RCCB. • Height Adjustment: The delivered height of your cooker is set at 902 mm to the top of the hob side trims. The minimum height of the cooker is 900 mm If the plastic feet under the plinth are removed, with care, using a suitable tool. Levelling washers/height adjustment washers - 1 x 10 mm and 2 x 2 mm for each foot (packed in a polythene bag) are provided for use when the cooker is sited on an uneven floor. You can Increase the height, by plugging the levelling washers into the plastic feet (under the plinth) to 902, 904, 910, 912 or 914 mm to ensure that the cooker Is level and does not ‘rock’. A second person should hold the cooker whilst it is lifted backwards to gain access to the feet. The cooker should not be installed with the hob height below the worktop height. Before sliding the cooker into position, measure that height of the units next to the cooker from the floor to the worktop at front and back. Lower top oven door, place hands on the top oven roof avoiding any damage to the grill elements and carefully locate cooker Into position. Check the level of the cooker by placing a spirit level on the top of the cooker facia taking care not to scratch the surface. Make any adjustments necessary. The maximum loading of your cooker is 11.16kW. NOTE: Children should not be allowed to play with the appliance or tamper with the controls. 2 23 Hotpoint Service Cover Satisfaction Guaranteed or Your Money Back Hotpoint gives you a unique ‘Satisfaction Guaranteed' promise-valid for ninety days after you have purchased your Hotpoint product. If there is a problem with your Hotpoint appliance just call your Hotpoint Service Office. If necessary we will arrange for an engineer to call. If the problem is not resolved by us under this Guarantee, Hotpoint will replace your appliance or, If you prefer, give you your money back. This Guarantee Is additional and subject to the terms of Hotpoint’s Five Year Parts Guarantee. Hotpoint’s Free Five Year Guarantee From the moment your appliance is delivered, Hotpoint guarantees It for FIVE YEARS. • In the Five Years all replacement parts are FREE provided they are fitted by our own Service Engineer. During the first year our Engineer's time and labour Is also free. • After the first year we will charge for our Engineer’s time and labour. We do, however, operate a range of Service Plans (see opposite) which for an annual payment enables you to cover any repair costs which may be necessary. • All of our service repairs are guaranteed for twelve months in res...