Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
• To ensure the stable placement of the gas hob, please ensure that after the tapping, the vertical sides of the installation site are smooth. • Follow the method shown in the illustration on the left and clamp the four spring sheets supplied with the product to the corresponding four installation positions on the back shell. • After installing the spring sheets, push the entire gas hob firmly into the cutout opening in the countertop, until the outside rim of the gas hob is seated closely on the countertop. 8 Installation Instructions The connection of the gas hob must be performed by a qualified technician, and it must conform with the legal provisions and connection requirement. The indoor gas hose behind the gas meter and the air inlet at the bottom of the gas hob should be connected with a metal bellows and a special rubber hose whose length should be connected with a metal bellows and a special rubber hose whose length should not exceed 1.5m.(Please refer to the appropriate requirements filed by the local gas management department. You can consult and purchase the special hose and hose clip at counters for gas products in hardware stores). We recommend you to use the metal bellows to attach the connecting hose. Especially, if the other appliances are installed under the hob such as a disinfecting cabinet, backing oven and microwave oven etc, a gas rubber hose must not be used for the gas connection. Using a gas rubber hose for the gas connection - The multi-directional air inlet used for connecting the hose is provided in the packing case of gas hob. - The two ends of the gas hose are connected to the gas hob and the indoor gas valve (the inside diameter of the gas hose is 9.5mm). - When connecting the gas hose, you must insert the gas hose until it reaches the red line on the multi-directional air inlet, and secure it firmly in position with a hose clip. - After the connection is completed, please make sure that the gas hose is not flattened, twisted or bent by any other objects. Then smear soap suds all over the hose connection part; and check each part of the connection hose carefully to see if there is any leakage. - We recommend that you perform an airtight test for the gas hob periodically while it is in use, or else replace the gas hose annually. - Do not leave the gas hose in a high temperature area or put it contact with any high temperature section of the gas hob. Connecting the gas pipeline 9 Gas leak detection Installation Instructions Leak detection Attention! After he gas pipeline connection has been completed, the leak detection test must be performed. Smear the suds on each connection part with a soft brush, and then open the gas valve to check carefully if bubbles appear, please close the gas valve immediately, and adjust the air inlet connection until no bubbles appear. Installing the electrical source Connection the electrical source The electrical source is fixed in the middle of bottom, when you use it, please confirm it is safety and grounded. Please confirm the hob wire are grounded, it is used attached a tri-pins, and the tri-pins are grounded, when it is creepage, the setting can prevent human from getting an electric shock. We suggest the flashboard is fixed on the right underside, be far away from the gas and air inlet. As shown in the below picture, please make sure that the knobs, burner heads, caps and supports have been installed correctly. Incorrect installation will seriously affect the normal use of the product and shorten its lifespan. When installing the supports and burners, the user should pay attention that the protruding objects on the bottom of the supports and burners are aligned with the stretching slot on the faceplate, which is used for maintenance. If you place the components randomly or rotate them for hob placement, the stainless steel faceplate may be scratched. The appearance damage of the gas hob resulting from such installation operations is not covered by our warranty. Installing the electrical source Installing the supports, caps and burners size of tapping surface 10 Installation Instructions PBD7251 PBD7351 PBD7331 11 Operation Instruction Getting familiar with your new hob • Top view of product PBD7251 Faceplate Knob Burner head Three-ring cap Internal cap Main support Double-ring cap PBD7351 Burner head Internal cap Faceplate Knob Small support Main support Cap base Three-ring cap Double-ring cap PBD7331 • Back view of product Burner head Internal cap Faceplate Knob Small support Main support Cap base Three-ring cap 12 Operation Instruction 16 14 2.9 LPG JZY-PBD7331E40B 2.0 Natural gas JZT-PBD7331E40B PBD7351 PBD7331 Power V 220 Rating heat input (left/right) kw 4.0 —— Gross weight kg 15 20 Net weight kg 13 18 Size of tapping (W.D)mm 700 .400 Fillet 4 .R20 Dimension (W.D.H)mm 785.450 .155 Rating heat input (mid) kw —— 1.7 Heat load of burner kW Gas pressure kPa 2.0 2.9 2.0 2.9 Natural gas LPG Natural gas LPG Appropriate gas JZY-PBD7351E40T ...
Ce manuel est également adapté pour les modèles :Hobs - PBD7251SG/01 (1.73 mb)
Hobs - PBD7331MS/01 (1.73 mb)
Hobs - PBD7351MS/01 (1.73 mb)
Hobs - PBD7351SG/01 (1.73 mb)