Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
and make new settings. ™ and ‚ flash alternately in the lower display and ‹ lights up in the upper display. 3. Touch the w symbol repeatedly until the desired indicator appears in the bottom display. 4. Set the desired value on the settings range. Cleaning and care The information in this section provides help on how best to care for your hob. Suitable maintenance and cleaning products can be purchased from the after-sales service or in our e-Shop. Ceramic Clean the hob after each use. This will prevent spills from burning onto the ceramic. Only clean the hob when it has cooled down sufficiently. Use only cleaning agents which are suitable for glass ceramic. Follow the cleaning instructions on the packaging. Never use: ¦ Undiluted washing- up liquid ¦ Detergent intended for dishwashers ¦ Scouring agents ¦ Harsh cleaning agents such as oven spray or stain remover ¦ Abrasive sponges ¦ High-pressure cleaners or steam jet cleaners Ground-in dirt can be best removed with a glass scraper, available from retailers. Please note the manufacturer's instructions. You can also obtain a suitable glass scraper from our after- sales service or from the e- Shop. Using special sponges to clean glass ceramic achieves great cleaning results. Hob surround To prevent damage to the hob surround, observe the following instructions: ¦ Use only hot soapy water. ¦ Wash new sponge cloths thoroughly before use. ¦ Do not use any sharp or abrasive agents. ¦ Do not use the glass scraper. Rectifying faults Faults often have simple explanations. Please read the following notes before calling the aftersales service. Display Fault Measure Blank There is no power supply. Check the household fuse for the appliance. Check whether there is a power cut by trying other electronic appliances. All displays flash The controls are damp or an object is resting on them. Dry the controls or remove the object. ”. The electronics have overheated and have switched off the corresponding hotplate. Wait until the electronics have cooled down sufficiently. Then touch a control for the hotplate. ”… The electronics have overheated and have switched off all hotplates. Wait until the electronics have cooled down sufficiently. Then touch any control. ”† and the heat setting flash alternately The electronics may overheat due to a pan placed on the electronics. Remove the pan. The display ”† and the audible warning signal end a short time after this. ”† A pan that is too hot has been placed on the electronics. The electronics have overheated and have switched off the corresponding hotplate. Remove the pan. Wait until the electronics have cooled down sufficiently. Then touch a control for the hotplate. ”‰ The hotplate was in operation for too long and has switched itself off. You can switch the hotplate back on again immediately. After-sales service Our after- sales service is there for you if your appliance should need to be repaired. We are committed fo find the best solution also in order to avoid an unnecessary call- out. E number and FD number: Please quote the E number (product number) and the FD number ( production number) of your appliance when contacting the after-sales service. The rating plate bearing these numbers can be found on the appliance certificate. Please note that a visit from an after-sales service engineer is not free of charge, even during the warranty period. Please find the contact data of all countries in the enclosed customer service list. To book an engineer visit and product advice GB 0844 8928979 Calls from a BT landline will be charged at up to 3 pence per minute. A call set-up fee of up to 6 pence may apply. IE 01450 2655 Trust the expertise of the manufacturer, and rest assured that the repair will be carried out by trained service technicians using original spare parts for your domestic appliance. Test dishes This table has been produced for test institutes to facilitate the testing of our appliances. The data in the table refers to our accessory cookware from Schulte Ufer (4-part induction pot set HEZ 390042) with the following dimensions: ¦ Saucepan dia. 16 cm, 1.2 litres, for 14.5 cm dia. hotplate ¦ Cooking pot dia. 16 cm, 1.7 litres, for 14.5 cm dia. hotplate ¦ Cooking pot dia. 22 cm, 4.2 litres, for 18 cm dia. or 17 cm dia. hotplate ¦ Frying pan dia. 24 cm, for 18 cm dia. or 17 cm dia. hotplate Heating up/ bringing to boil Ongoing cooking Test dishes Heat setting Cooking time ( min: sec) Lid Ongoing cooking Lid setting Melting chocolate Ovenware: Saucepan Chocolate couverture (e. g. Dr. Oetker --- 1 No Zartbitter, 150 g) on 14.5 dia. hotplate Heating and keeping lentil stew warm Ovenware: Cooking pot Lentil stew made to DIN 44550 Initial temperature 20 ° C Amount 450 g for 14.5 cm dia. hotplate 9 approx. 2: 00 without stirring Yes 1. Yes Amount: 800 g for 18 cm dia. or 17 cm 9 approx. 2: 00 without stirring Yes 1. Yes dia. hotplate Lentil stew from the tin e. g lentil with Erasco sausages: Initial temperature 20 ° C Amount 5...