Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Fig. 8. Ensure that it is completely tightened in order to guarantee the seal.. Fig. 8 Set the control knobs to minimum. Remove the control knobs from the taps. Fig. 9. It has a flexible rubber valve reinforcing ring. Simply press on this seal with the tip of a screwdriver to allow access to the tap adjusting screw. Adjustment of the taps Fig. 9 Never remove the valve reinforcing ring. Adjust the minimum ring setting by turning the by-pass screw using a flat head screwdriver. To adjust the minimum flame for N.G. replace the control knob onto the spindle, light the gas and turn the control knob to the small flame position. Screw the adjustment screw anti-clockwise to estabilish a minimum stable flame position. The flame should remain alight and not burn back to the injector when the valve is turned quickcly from ‘Full On’ to the “Minimum flame” position and back a few times. To adjust the minimum flame position for ULPG the screw must be fully tightened down clockwise. If the by-pass screw cannot be accessed, disassemble the grease splash tray, which is fixed to the rest of the hob using a clip and screw mounting system. The following steps must be taken to remove the grease splash tray: - Remove all the burner covers, pan supports and control knobs. - Loosen the screws on the burners. Use the disassembly lever 483196 availablle from our Technical Assistance Service. To release the front clips, apply the lever to the area shown in figure 10. Fig. 10 To assemble the grease splash tray again, proceed in the reverse order to removal. It is important that all the seals are refitted to form a seal. These devices are essential for the correct operation of the appliance as they prevent liquids and dirt from entering the appliance. Refit the control knobs. Never remove the tap spindle. In the event of a malfunction, change the whole tap.Fig. 11. Fig. 11 Warning! After finishing, the sticker indicating the new type of gas must be placed close to the specifications plate. Operating instructions Burner locations 415 4 15 6 23 327 4 1 Pan supports 2 Control knobs 3 Auxiliary burner (up to 1 kW) 4 Semi-rapid burner (up to 1,75 kW) 5 Rapid burner (up to 3 kW) 6 Double-flame burner (up to 3,3 kW) 7 Double-flame burner (up to 5 kW) The gas burners There are indications to show which burner each control knob operates. Fig. 12. Operation Fig. 12 It is essential to ensure that all the burner parts and pan supports are correctly installed for the appliance to work correctly. Fig.13-14. Fig. 13 Fig. 14 Switching on If your cooktop can be switched on automatically (ignition sparkers): automatically Safety system Ignition sparker Thermocouple Fig. 15 Switching off a burner Power levels 1. Press the chosen burner control knob and turn it anticlockwise to the maximum power setting. While the control knob is still pressed down, sparks are produced on all burners. The flame ignites (it is no longer necessary to press down the control knob). 2. Turn the control knob to the required setting. If it does not come on, turn the control knob to the off setting and repeat the steps above. This time, press and hold the control knob for longer (up to 10 seconds). Warning! If after 15 seconds the flame does not ignite, switch off the burner and open a nearby window or door. Wait at least one minute before trying to switch the burner on. Depending on the model, your cooktop may have a safety system (thermocouple) that prevents the flow of gas if the burners accidentally switch off. To ensure that this device is active, switch on the burner as usual and, without releasing the control knob, press and hold it down firmly for 4 seconds after lighting the flame. Fig. 15. Turn the corresponding control knob clockwise to the 0 setting. The progressive control knobs can be used to control the power needed, from minimum to maximum power. Setting U Control off Large flame › Maximum capacity or aperture and electricity on Economy flame oe Minimum capacity or aperture For double-flame burners, the inner and outer flames can be controlled separately. The available power levels are as follows: Inner and outer flame on full power. Outer flame on minimum, inner flame on full power. Inner flame on full power. Inner flame on minimum power. Warnings It is normal to hear a slight whistling noise while the burner is operating. When it is first used, it is normal for the burner to give off odours; this does not pose any risk and does not indicate a malfunction; they will disappear in time. A few seconds after switching off the burner, it will make a sound (thud). This is not a fault - this means that the safety device is no longer operating. Keep the burner as clean as possible. If the ignition sparkers are dirty they will not light properly. Clean them periodically using a small non-wire brush. Bear in mind that the ignition sparkers must not suffer any serious impacts. An orange-coloured flame is normal. This is caused by the presence of dust in the atmosphere, spil...
Ce manuel est également adapté pour les modèles :Hobs - T22S46N0AU/03 (2.56 mb)
Hobs - T22S46N0AU/07 (2.56 mb)
Hobs - T26S66N0AU/01 (2.56 mb)
Hobs - T26S66N0AU/03 (2.56 mb)