Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
These may be damaged by the very high temperatures. Place the pans on the pan supports, never directly on the burner. Make sure that the pan supports and burner caps are correctly positioned before using the appliance. Pans should be placed on the hob carefully. Do not strike the hob and do not place excessive weight on it. Care and cleaning In this chapter you will find tips on how to maintain and clean your cooktop correctly. m Risk of burns! The appliance becomes hot during operation. Allow the appliance to cool down before cleaning. m Risk of electric shock! Do not use high pressure washers or steam cleaners to clean the appliance. Cleaning Clean the appliance after every use once it has cooled down. Remove spills immediately. Burnt in residues may be difficult to remove. Assemble the burner parts and pan supports after cleaning and drying them. Make sure all burner parts are properly fitted. Burner ring and burner cover must lock in place and lie evenly flat. Part/surface Recommended cleaning method Stainless steel Clean with a soft cloth and some surfaces soapy water; polish dry with a soft cloth. Do not use too much water to avoid water entering the appliance. Caution! Damage to the seal: Do not clean the gap around the stainless steel surface with sharp objects. Only clean with a soft brush. To remove stubborn residues or discolouration because of the heat, you can order a stainless-steel cleaner (order number 464524) from your specialist retailer or our after-sales service. Pan support Carefully take off pan supports for cleaning. Soak in soapy water. Clean with a brush and some detergent. Be careful when cleaning around the rubber rests to ensure they do not come loose. Rinse with clear water. Carefully dry pan support before assembly. Do not clean in a dishwasher! Control knobs Clean with a soft, moist cloth and some soapy water; do not use too much water. Caution! Damage to the appliance: Do not pull off the control knobs to clean them. Burner parts Rinse with clear water. Carefully dry burner parts before assembly. Do not clean in a dishwasher! Ignition sparkers If required, clean with a fine brush. Burnt-in residues To remove stubborn, burnt-in residues you can order the grill cleaning gel (order number 463582) from your specialist retailer or from our after-sales service. You can use it to clean the pan supports, the burner parts and the stainless steel cooktop base. If necessary apply the gel and leave overnight. Please observe the manufacturer’s instructions. Do not use these cleaners ¦ scouring or chemically aggressive cleaners ¦ cleaners containing acid (e.g. vinegar, citric acid, etc) ¦ cleaners containing chloride or with a high content of alcohol ¦ oven cleaner ¦ hard and scratchy sponges, brushes or scouring pads ¦ carefully rinse new sponge clothes before the first use Trouble shooting Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. Fault Possible cause Solution Malfunction of the The household fuse has tripped. Check the fuse box if the fuse has tripped. general electrical system. The electric ignition does There may be food or cleaning products The space between the ignition sparker not work. stuck between the ignition sparkers and and the burner must be clean. the burners. The burners are wet. Dry the burner caps carefully. The burner caps are not correctly Check that the burner caps are correctly positioned. positioned. Power cut Ignite the burner with a lighter or a match. The burner flame is not The burner components are not correctly Ensure the components are correctly uniform. positioned. positioned. The grooves on the burner are dirty. Clean the grooves on the burner. The gas flow is not The gas supply is blocked via gas taps. Open all gas taps. normal or there is no gas. If the gas is supplied from a gas cylinder, Change the gas cylinder. check that this is not empty. The kitchen smells of There may be a leak in the gas cylinder Check that the coupling is sound. gas. coupling. The burner goes off after The control knob was not held down for Once the burner is on, hold the control ignition. long enough. knob down a few seconds longer. Fully press control knob. The grooves on the burner are dirty. Clean the grooves on the burner. After-sales service In the event of repairs or if you need further accessories or spare parts, please contact our after-sales sevice. You can find the addresses in the enclosed after-sales service directory. When contacting the after-sales service, please specify the E-number and FD- number of the appliance. You can find these on the rating plate on the bottom of the appliance. For future reference you can note the data of your appliance and the telephone number of our after-sales service here. Please note that you will be charged for calling out an after-sales service technician, even within the warranty period, should the problem result from an operating error. E-Nr. FD-Nr. After-...
Ce manuel est également adapté pour les modèles :Hobs - T28V66N0NL/01 (453.94 kb)
Hobs - T28Z66N0/01 (453.94 kb)