Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
The appliance may be installed in kitchen combinations made of wood or similar combustible materials without taking additional measures. The rear wall must consist of non-combustible material. A minimum distance of 100 mm from heat-sensitive items of furnishing or contact surfaces (cupboard side panel) must be observed. The hob conforms to appliance class 3 and must be installed in the worktop as shown in the installation sketch. Do not install the appliance under a suspended cupboard. For installation under a vapour extractor, a minimum clearance of 650 mm from the top edge of the pot stand to the bottom edge of the wall hood must be observed. If several gas appliances are installed, a larger distance from the extractor hood might be needed. Observe the installation manual of the extractor hood. Wall trims must be heat-resistant, and the minimum distance between the hob and the wall trim is at least 35 mm. The appliance must be installed and connected by an authorised gas installer. The installation must conform with all current regulations of the gas supply companies and the regional construction regulations. Technical modifications reserved. Connecting the Appliance 105 28 1/2 " 50 max. Electrical connection Electrical connection (AC 220-240 V) is established by means of a connecting cable with an earthing contact plug connected to an earthed socket, which must also be accessible after installation of the gas hob. If, after installation of the gas hob, not all poles can be isolated from the mains by removing the plug, an isolating device with a contact gap of at least 3 mm must be permanently installed. When establishing connections, make sure that the connecting lead cannot come into contact with hot parts of the gas hob or other hot parts. Turn the control knob to the OFF position before connecting the appliance to the power supply. Gas connection The gas connection must be in a location that permits access to the shut-off valve and which, if applicable, is visible after opening the door of the cabinet. By means of the included R 1/2“ connection bracket (on the appliance end) with the affiliated washer, the appliance must be connected to a fixed connecting line or a gas safety hose to DIN 3383 Part 1 that corresponds to the type concerned. An ambient temperature of 70 °K must not be exceeded if the gas safety hose consists only partly of metal. The permissible ambient temperature for a gas safety hose that consists completely of metal is 115 °K. If a flexible line is used, it must be laid in such a way that it cannot come into contact with moving parts of the kitchen element (e.g. drawer). The mains connecting cable must at least correspond to type H 05 V2V2 3G 0.75 or it must be correspondingly heat-resistant (at least 90 °C). The mains connecting cable must only be purchased through and connected by an authorised specialist. Pay attention to the information on the rating plate and connect the PE conductor. Connect the connecting cable to the mains. Preparing the Cabinet 15751170 360 45 380 490min. 50 min. 35 180 510130 8 765 1,4 m 123 35 60 • Cut out the recess for the hob in your worktop. Proceed as indicated on the installation sketch. The installation sketch contains the measurements of the space required for the trim between the appliances. Several appliances can also be installed in individual recesses, as long as a minimum clearance of 50 mm is kept to between the appliances. • As shown in the installation sketch, drill the O35 mm hole to secure the control knob in the cabinet front. • If the cabinet front is thicker than 26 mm, the front must be routed from the back to max. 26 mm on an area of 80 x 310 mm. min. 5 min. 5 D > 26 D = 26 80 x 310 16 – 26 Installing the Cooker Please note: If you want to convert the appliance to a different type of gas, change the nozzles before installing the appliance (see pages 22 -23). • Before installation, remove all styrofoam packaging from the control knob and peel off the protective film. • Hold the support plate from the rear against the cabinet front, insert control knob into the hole, secure from the rear with the nut. Secure the support plate additionally with the supplied wood screw to prevent turning. • Undo trough securing nuts and carefully detach the trough. Note: if a flexible gas connection is being used, you can connect the appliance before installing it into the worktop. • T urn the clamping screws to the side. Insert the hob with the Gaggenau logo on the front into the cut-out and align it. Note: do not stick the hob onto the worktop with silicone. • T urn the clamping screws under the countertop and tighten them evenly. Do not tighten the clamping screws too tightly, as a uniform sealing gap should be left all round. • Connect the appliance to the gas supply. • Check the installation for gas leaks. Installing the Spindle min. 5 105-162,5 < 300 SV 401-205 o 35 < 60< 140 StandardSV 401-090 o 60 38 spindle cover The numbers correspond to the di...
Ce manuel est également adapté pour les modèles :Hobs - VG411110F/01 (803.06 kb)
Hobs - VG411210/01 (803.06 kb)
Hobs - VG411210AU/01 (803.07 kb)
Hobs - VG411210CA/01 (803.07 kb)