Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Hobs - PPH616B21A/03 (3.28 mb)
Hobs - PPH616B21A/03 (2.55 mb)
Hobs - PPH616B21A/03 (898.86 kb)
Facilité d'utilisation
Wiring Code ¦ Local Electrical Regulations ¦ Any other statutory regulations Preparing to install Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to be inserted in a benchtop cutout. Only an officially authorised technician should connect the appliance. Before you begin, turn off the gas and electricity supply. Before connecting the unit, check whether the local connection conditions (type of gas) are compatible with the unit’s setting. Observe any special conditions imposed by local suppliers (utilities). The specifications of this cooktop are stated on the data label located on the bottom of the cooktop base. A duplicate data label is supplied for adhesion to an accessible location near the hotplate if the data label on the base of the hotplate cannot be accessed when the hotplate is installed. Clearances A range hood fitted above the top must be installed according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a range hood and 750 mm for an exhaust fan. Any adjoining wall surface situated within 200 mm from the edge of any hob burner must be a suitable non-combustible material for a height of 150 mm for the entire length of the hob. Any combustible construction above the hotplate must be at least 650 mm above the top of the burner and no construction shall be within 450 mm above the top of the burner. A minimum depth of 50 mm from the top of the worktop surface must be provided for the appliance. If the base of the hotplate can be touched, a protecting shield must be fitted. ¦ The shield must be at least 10 mm from the lowest part of the hotplate and must be capable of withstanding the appliance temperatures. Minimum thickness of benchtop is 30 mm. ¦ The shield material must be mdf or similar with minimum thickness of 12 mm. ¦ The shield overall dimensions must be 560 mm wide x 480 mm deep. ¦ Provide cut-out in right hand rear of shield of 80 mm wide x 80 mm deep to provide for gas regulator / LP connection fitting. After installation of the shield the clearance around the top and sides of shield will allow adequate ventilation. Ensure the side and top clearances are not obstructed. . If an oven is positioned below the cooktop the barrier does not need to be fitted, but a space of 35 mm must be maintained between the underside of the cooktop and the top of the oven. Installation of cooktop into the kitchen bench Side clearances: If the distance measured from the periphery of the nearest burner to any vertical surface is less than 200 mm, the surface shall be protected in accordance with clauses 6.10.1.2 of AS/NZS 5601.1. Make an appropriate size cut in the worktop surface, depending on the installation method: standard (a) or flush (b). For flush installation: ¦ All cuts in the worktop surface should be done by a specialised shop. ¦ The cuts should be clean and precise, as the cut edge is on the surface. The stability of the furniture should also be ensured after cutting work. ¦ Use only specially designed work surfaces, resistant to high- temperature and water (e.g. natural stone or tiled). ¦ Surrounding furniture must be resistant to temperatures up to 90 °C. Installation procedure: a) Standard installation Depending on the model, the adhesive seal may be factory- fitted. If this is the case, it should not be removed under any circumstances, since the adhesive seal prevents leaks. If the seal has not been factory-fitted, apply it to the underside of the hob. Fitting the appliance onto the kitchen unit: 1. Remove the clips from the accessory bag and screw them into the position indicated so that they can turn freely. 2. Insert and centre the hob. Press the sides of the hob until it is supported around its entire perimeter. 3. Turn the clips and tighten them fully. The position of the clips depends on how thick the work surface is. b) Flush installation 1. Complete a normal installation of the appliance making sure that it is surrounded by a uniform slot. The hob surface should be slightly below the work surface. For tile worktops, if necessary, raise the bearing surfaces with strips resistant to water and temperatures. 2. Check the operation and position of appliance. 3. Fill the gap between the worktop and hob with conventional silicone adhesive appropriate in the colour you desire. Note: If unsuitable silicone adhesive is used on natural stone surfaces then this can produce colours that can not be removed. Our Technical Assistance Service can provide you with the most suitable glue (code 310818). Please note the manufacturers instructions for use. 4. Smooth the silicone adhesive with a scraper or wet finger moistened with soap and water before it forms a layer. 5. Allow the silicone adhesive to dry before using the appliance. Connection Electrical An electrical 10 amp socket needs to be within 1 m of the hotplate to allow electrical connection. The socket must remain acce...
Ce manuel est également adapté pour les modèles :Hobs - PPH616B21A/24 (3.35 mb)
Hobs - PPQ716B21A/03 (3.35 mb)
Hobs - PPQ716B21A/24 (3.35 mb)