Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
Your Specialized SpeedZone® Elite has been designed to provide the best combination of performance, features, durability and ease of use and installation. This computer • Second Wheel • Easy Calibration • Wireless Mounting • Heavy-duty abrasion pick-up wire • Water resistant housing • 2 Year Warranty • Backlit LCD display What is included in your SpeedZone Elite package: 1. SpeedZone ® computer (1) 2. Mounting bracket wired for cadence (1) 3. Mounting bracket w/out cadence wiring (1) 4. Magnet with screw (1) 5. Cadence magnet (1) 6. Cable tie wraps (8) 7. Mounting bracket sizing straps (3) 8. Transmitter (1) 9. Transmitter mounting bracket (1) 1 2 3 4 6 5 7 8 9 500-700mm 20-28 in. FIGURE 1: FIGURE 2: SENSOR MAGNET PLACEMENT ATTACHMENT MOUNTING THE SPEEDZONE ® ELITE The SpeedZone ® Elite wireless transmitter can mount on the right or the left side of the fork blade. The right side should be used on large frames or when a suspension fork is installed. The optimal and the (610mm) The distance less than 24 inches temperatures are To reduce signal loss in colder the transmitter should mounted as close to the computer possible. (Maximum mounting distance is 28 inches). Use the transmitter-mounting bracket and tie-wraps provided to position the sensor. Do not tighten the tie-wraps until final placement of the magnet is correct. (See figure 1) . Attach the magnet to a spoke across from the transmitter with the magnet screw. The clearance between the magnet and the transmitter should be approximately 1/32"-1/16" (1-2mm). Tighten the Do not over-tighten (See figure 2) . Attach the mount using the bracket screw Tighten so that the bracket rotate on the handlebar. There are several sizing straps provided to diameter bars. (See figure 3) . Slide the computer forward onto the mount until it ‘snaps’ into place with an audible click. To remove the computer, push it backward until it releases from the mount. To test for proper installation of the magnet, transmitter and computer, activate the computer by pushing the ‘MODE’ (right side) button. Pick up the front of the bicycle and spin the front wheel. The "wheel option" indicator will flash. If it does FIGURE 3: MOUNTING BRACKET not flash, check the sensor and magnet alignment. Realign as necessary until the "wheel option" indicator flashes while spinning the wheel. MOUNTING CADENCE HARDWARE In order to use the cadence option you must install the mounting bracket with the wired sensor provided with your SpeedZone ® Elite. Run the cadence sensor wire tube and chain and secure it into provided tie-wraps. (See figure 4) Next, attach the cadence the inside of your crank directly across from the sensor. Use a tie-wrap to fasten the magnet to the crank (See figure 5) . Do not tighten the tie-wrap until final FIGURE 4: CADENCE WIRE PLACMENT FIGURE 5: FIGURE 6: CADENCE SENSOR CADENCE MAGNET PLACEMENT ATTACHMENT placement of the magnet is correct. The clearance between the magnet and the sensor should be approximately 1/32"-1/16" (1-2mm). (See figure 6) Tighten the magnet and sensor. PROGRAMMING Programming SpeedZone ® Elite requires it placed in various odometer mode, distance computer can be cycled modes by pressing the "MODE" located on the right-hand side housing. Once a specific mode has been entered, its values can be reset or adjusted by pressing either the "FUNCTION" button located on the left hand side of the housing or by using a combination of the "MODE" and "FUNCTION" buttons. 1. Miles or Kilometers selection Your SpeedZone ® Elite will record speed and distance in either miles (M/h) or kilometers (Km/h). To enter your selection push the "MODE" (odometer) appears the display (This is mode). Hold down the (left side) button and ‘tap’ button once. The Km/h, m/will begin blinking. You may now alternate between miles and kilometers pressing the "MODE" button. When the correct choice is flashing, select it by pressing the "FUNCTION" button. You will now enter the "Programmable Odometer" mode. If the odometer setting is correct push the "FUNCTION" button five times to exit odometer mode. (Otherwise, see "Setting the programmable odometer" below). 2. Setting the Odometer This mode is useful replaced the battery and would like retain the mileage you ridden. To access the programmable odometer mode, first advance "MODE" button until (ODO) appears on the left-hand side of the screen. Hold down the "FUNCTION" button and ‘tap’ the "MODE" button once. The Km/h indicator will flash. If the Km/h setting is correct press the "FUNCTION" button once and a five-digit number will appear. You are now in the programmable odometer mode. To enter a mileage into the odometer, press the "MODE" button until the flashing digit is correct. ( Note: The "MODE" held to scroll the "FUNCTION" next digit to the right. process until all five digits as your existing mileage. 3. Wheel Circumference Selection To set the circumference for the type tires you are using, you can use Specialized’s "Easy Calibratio...