Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
4. Unfold the CONSOLE WIRE HARNESS from the POST extending from the FRAME. NOTE: THE COLLAR (#4) SHOULD ALREADY BE IN PLACE INSTALLED ON THE HANDLEBAR ASSEMBLY (#5). IF NOT, INSTALL BEFORE PROCEEDING. 5. Place the HANDLEBAR ASSEMBLY (#5) on the floor in front of the FRAME with the two CONNECTORS next to each other. Align the two CONNECTORS and push them together until they firmly snap into place. 6. Position the HANDLEBAR ASSEMBLY (#5), with the COLLAR (#4) in place, so that the HANDLEBAR is facing away from the user. Slide the HANDLEBAR ASSEMBLY into the HANDLEBAR POST. Be careful not to pinch the wires. Align the three holes in the HANDLEBAR ASSEMBLY (#5), with those in the HANDLEBAR POST and install the three HANDLEBAR BOLTS (#1). NOTE: BE CAREFUL NOT TO DAMAGE THE WIRES WHEN PASSING THE BOLTS THROUGH THE HOLES. TIGHTEN THE BOLTS SECURELY. 7. Slide the COLLAR (#4) down until it completely covers the HANDLEBAR ASSEMBLY HARDWARE and the HANDLEBAR POST. Secure the COLLAR by squeezing the sides and pushing downward firmly. 7 B A C 1 8P 1 5 5 4 8. There is a large hole in the rear of the display console (#6) through which you can see a 10-pin connector and a 4-pin connector. These correspond to the matching connectors on the wire harness protruding from the top of the handlebar. Model C7i Only: Properly align the locking tabs of the 16-PIN CONNECTOR (16P) on the WIRE HARNESS with the 16-PIN CONNECTOR on the back of the DISPLAY CONSOLE, then snap them together. Next, align the locking tabs of the 3-PIN CONNECTOR (3P) on the WIRE HARNESS with the 3-PIN on the back of the DISPLAY CONSOLE and plug them together until they SNAP into place. Model C9i Only: Properly align the locking tabs of the 10-PIN CONNECTOR (10P) on the WIRE HARNESS with the 10-PIN CONNECTOR on the back of the DISPLAY CONSOLE, then snap them together. Next, align the locking tabs of the 4-PIN CONNECTOR (4P) on the WIRE HARNESS with the 4-PIN on the back of the DISPLAY CONSOLE and plug them together until they SNAP into place. 9. Feed the WIRE HARNESS back into the HANDLEBAR TUBE. Attach the DISPLAY CONSOLE (#6) to the HANDLEBAR ASSEMBLY using the four CONSOLE SCREWS (#2) and a Phillips screwdriver. Tighten the four SCREWS in a crisscross pattern. CAUTION!: BE CAREFUL NOT TO OVERTIGHTEN THE SCREWS. 10. To install the 9-VOLT ALKALINE BATTERY (#8) found in the parts bag use a Phillips screwdriver to remove the screw from the back door. Gently pull the BATTERY WIRES from the back of the DISPLAY CONSOLE and connect them to the 9-VOLT ALKALINE BATTERY. Carefully, tuck the BATTERY WIRES back into the DISPLAY CONSOLE and set the BATTERY in place. Re-install the BATTERY DOOR by inserting the bottom tab of the BATTERY DOOR into the corresponding slot in the DISPLAY CONSOLE. Push the DOOR into place and tighten the screw with a Phillips screwdriver. CAUTION!: BE CAREFUL NOT TO OVER TIGHTEN THE SCREW 11. After placing the Lifecycle exercise bike in the intended location for use, check the stability of the bike. If the bike is not level, rotate the FOOT in the STABILIZER BAR that appears to be higher until the Lifecycle is level. Secure the position of the FOOT by tightening the LOCKNUT with the enclosed wrench. 6 10P 4P 3P 16P E D 8 FOOT PRE-OPERATION CHECKLIST 4 Insure that the STABILIZER BAR and HANDLEBAR BOLTS are tight. 4 Make sure the exercise bike is properly leveled and stable. 4 Confirm the display console is set to English or metric units. (See Optional Settings ENG/MET in Operation Manual.) 4 Read the entire Operation Manual before using the exercise bike. Before attempting to operate your Lifecycle recumbent exercise bike, it is imperative that you familiarize yourself with the contents of the Operation Manual. If your recumbent exercise bike does not respond as described in the OPERATION MANUAL c...
Ce manuel est également adapté pour les modèles :Vélos - C7 (293.41 kb)