Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
13. Always make sure tires are properly inflated (see page 2). WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking your Tricycle with Pneumatic Tires, check to make sure all parts listed on page 5 are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. Assembly Your Rolling Tricycle with Pneumatic Tires will require complete assembly. It is important that you read the entire manual to become familiar with the product BEFORE you assemble and use the Tricycle. Before assembling the Tricycle be sure that you have all parts described in the Parts List and Assembly Diagram located on the last pages of this manual. THE RIDER OF THE TRICYCLE MUST BE AT LEAST 48”TALL TO PROPERLY REACH THE PEDALS. Handlebars 1. To attach the Handlebar (1), loosen Nut (31) and slide out Bolt (33) and Washer (32). Insert Handlebar (1)-see Figure 1. Adjust Handlebar so that it is centered on the Stem (8) and set at the angle that is most comfortable for the rider. Now insert Bolt (33) with Washer (32) and thread on Nut (31). Tighten into place. Apply pressure to the Handlebars(1) to make certain that they do not rotate. 2. Slide a Grip (2) onto the end of each Handlebar (1). 3. Insert the Handlebar (1) and Stem (8) down through the Locknut (5), Upper Cap (7), and Bearing Ring (36) and into the Frame (13). Lock Bolt (3) Bolt (33) Nut (31) Washer (32) Handlebar (1) Figure 1 Stem (8) SKU 94142 For technical questions please call 1-800-444-3353. Page 3 CAUTION: Make certain that the Stem (8) and Handlebar (1) are set at an appropriate height for the rider. Make certain that the Stem (8) is not raised beyond where it is secure in the Frame (13). Make certain it is stable and tightly in place before riding the Tricycle. 4. To raise or lower the Stem (8), use a hex wrench to loosen the Lock Bolt (3). Gently pull up on the Stem (8) or push it down until it is at the desired height. Make certain that it is centered with the frame and Front Wheel (26). Tighten the Lock Bolt (3) into place-see Figure 1. Attaching the Seat and Seat Bracket 1. Line up the Seat Bracket (11) with one of the two sets of holes in the frame-see Figure 2. Insert Bolt (9) and thread on Lock Nut (34). 2. If desired, the Seat (10) can be rotated up and down or moved forward or backward by loosening the Nut located directly under the Seat (10). Figure 2-Seat and Seat Bracket Seat Bracket (11) Nut under Seat (10) Axle (35) Cotter Pin (14) Figure 3-Rear Wheel Attaching Rear Wheels 1. Slide one Rear Wheel (15) onto the Rear Axle (35). Slide on Washer (16) and insert Cotter Pin (14) through the outside hole in the Axle (35)-see Figure 3. Repeat for second Rear Wheel (15)-see Figure 3. Replacing Front Wheel 1. To fix or replace the Front Wheel (26), first remove Screws (24) from Front Wheel (26) rim- see Figure 4 and Assembly Diagram on page 6. Pull out Front Axle (25) and remove the Front Wheel (26). To put it back in position, line up Front Wheel (26) with holes in the Fork (29). Insert Front Axle (25), and thread in Screws (24). Screw (24) Front Wheel (26) Fork (29) Figure 4 SKU 94142 For technical questions please call 1-800-444-3353. Page 4 Pin (12) Pin (12) Maintenance Inserting the Pin 1. The Tricycle can be set-up to carry a small cart or trailer (neither is included) behind it by attaching them to the rear of the Tricycle. Unhook the Pin (12) from the rear of the Tricycle. Attach the cart to the Tricycle, and insert the Pin (12) back through the carrier and Tricycle- see Figure 5. Figure 5 1. Check the tire pressure often. Make certain that tire PSI is correct (see Technical Specification on page 2). A low tire inflation will force the rider to exert greater energy to move the Tricycle. The tires may wear prematurely if the proper tire pressure is not maintained. 2. Wheels and Hubs should be greased periodically. Parts List Part # Description Quantity Part # Description Quantity 1 Handlebar 1 19a Crank (right) 1 2 Grip 2 20 Pedal 2 3 Lock Bolt 1 21 Screw 2 4 Sleeve 1 22 Nylon Cap 2 5 Lock Nut 1 23 Pin 2 6 Lock 1 24 Screw M6 4 7 Upper Cap 1 25 Front Axle 1 8 Stem 1 26 Front Wheel 1 9 Bolt M6 1 27 Lower Cap 1 10 Seat 1 28 Bearing Holder 1 11 Seat Bracket 1 29 Fork 1 12 Pin 1 30 Bearing 2 13 Frame 1 31 Nut M8 1 14 Cotter Pin 2 32 Washer 1 15 Rear Wheel 2 33 Bolt 1 16 Washer 4 34 Lock Nut 1 17 Nut M6 2 35 Rear Axle 1 18 Washer 2 36 Bearing Ring 1 19 Crank (left) 1 37 Bolt M8 1 Note: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Rev. 05/06 SKU 94142 For technical questions please call 1-800-444-3353. Page 5 Parts and Assembly Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MAN...