Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
--------------------------------------------------------------------------------- 0°C - 40°C(32°F - 104°F) TIRE SIZE L(mm) 20 x 1.75 1491 24 x 1 1753 24 x 3/4 Tubular 1785 24 x 1-1/8 Tubular 1795 24 x 1-1/4 1905 24 x 1.75 1890 24 x 2.00 1925 24 x 2.125 1965 26 x 1(559mm) 1913 26 x 1(650c) 1952 26 x 1.25 1953 TIRE SIZE L(mm) 26 x 1-1/8 Tubular 1970 26 x 1-3/8 2068 26 x 1-1/2 2100 26 x 1.40 2005 26 x 1.50 1985 26 x 1.75 2023 26 x 1.95 2050 26 x 2.00 2055 26 x 2.1 2068 26 x 2.125 2070 26 x 2.35 2083 TIRE SIZE L(mm) 700 x 25C 2105 700 x 28C 2136 700 x 30C 2170 700 x 32C 2155 700C Tubular 2130 700 x 35C 2168 700 x 38C 2180 700 x 44C 2224 TIRE SIZE L(mm) 27 x 1 2145 27 x 1-1/8 2155 27 x 1-1/4 2161 27 x 1-3/8 2169 650 x 35A 2090 650 x 38A 2125 650 x 38B 2105 700 x 18C 2070 700 x 19C 2090 700 x 20C 2086 700 x 23C 2096 CO.,LTD. CO.,LTD. CO.,LTD. CO.,LTD. CO.,LTD. CO.,LTD. CATEYE ASTRALE CC-CD100 CATEYE ASTRALE CC-CD100 CATEYE ASTRALE CC-CD100 CATEYE ASTRALE CC-CD100 OMAD TSC AT CATEYE ASTRALE CC-CD100 T C O M A D T S O M A D OMAD TSC AT L CR2032 CC-CD100N II MAINTENANCE/PRECAUTIONS • Do not leave the main unit exposed to direct sunlight when the unit is not in use. Do not disassemble the main unit, sensor and magnet. • Do not pay too much attention to your computer's functions while riding! Keep your eyes on the road and duly consider to traffic safety. • Check relative position of sensor and magnet periodically. • If mud, sand or the alike clogs between the buttons and the body, the movement of the buttons may be disturbed. Softly wash away such objects by water. • For cleaning, use neutral detergent on soft cloth, and wipe off later with dry cloth. Do not apply paint thinner, benzine or alcohol, to avoid damages on the surface. BUTTON FUNCTIONS .Mode Button (left button) The display mode mark shift in the illustrated sequence each time the button is pressed, and the corresponding data is simultaneously displayed on the sub-display. If the mode button is held for over 2 seconds, 24-hour clock will be displayed. .Start/Stop Button (right button) Measuring of the Trip Distance and Elapsed Time is simultaneously started or stopped when the Start/Stop button is pressed. During operation the speed scale symbol flickers. Pressing the mode button can shift the main display from Current Speed to Cadence when Auto Mode is functioning. .Set Button (middle button) When the Set Button is pressed in the stop state in each mode, the following value can be changed; • In (O) mode ........................... Wheel Circumference • In 24-hour Clock mode ......... 24-hour Clock • In (T),(D),(A) mode ............... on/off the Automatic Start/Stop 0RESET: Select any mode except Total Distance (O), and press the Mode button and Start/Stop button simultaneously. The memorized Trip Distance, Elapsed Time, Average Speed and Maximum Speed will be erased. (When the two buttons are pressed in O mode, the wheel circumference stored will be displayed.) 0ALL CLEAR: When the AC button is pressed, all data stored in memory (trip distance, speed scale, wheel circumference and clock time) will be erased. All displays illuminates, then the mile/h symbol alone appears. This operation should be executed only when irregular display occurs or no display appears. Since all the memories are erased, set the main unit again according to "Main Unit Preparation" MAIN UNIT PREPARATION 0The following must be completed before operation. A battery is already loaded in the main unit when purchased. .Setting Speed Scale Press AC button on the bottom of the main unit to clear all data (Fig.1). All displays will illuminate. Then “mile/h“ alone will be displayed as in Fig.2, “km/h“ and “mile/h“ are alternately displayed each time when the Start/Stop button is pressed. Select either as desired. Press the set button to set the speed scale. The display will changed as shown in Fig.3. .Setting the wheel circumference 1. How to measure the wheel circumference(Fig.4) Put a mark on the tire tread and ride the bike one full wheel revolution. Mark the start and the end of the revolution on the ground and then measure the distance between the two marks. This is your actual circumference. Or, the "Selecting Values Cross Reference Table" tells you an approximate circumference according to tire size. 2. Setting the wheel circumference The figures 2155, standard wheel circumference for 27", will flicker as shown in fig. 3. When using 2155mm without revision, press the Set button. Current Speed and Elapsed Time will be displayed and 2155mm is set. To revise 2155mm, press the Start/Stop button to increase the number by one or press the Mode button to decrease the number by one. When either button is held down, it will rapidly increase/ decrease. Choose a correct circumference between 10mm to 2999mm. When the desire figure appears, press the Set button. Current Speed and Elapsed Time will be displayed, then the figure you selected will be set. 3. Resetting or changing the wheel circumf...