|
Instructions Cateye, Modèle CC-ST200
Fabricant : Cateye Taille : 298.94 kb Nom Fichier : a8463596-2d37-4aaa-9973-141683b11585.pdf
Langue d'enseignement:
|
|
|
|
Aller à la télécharger
Facilité d'utilisation
Nos. 4636769/4642606/5236759/5226340 and Design Patented Copyright© 1999 CATEYE Co., Ltd. CCMSTxch1-991124 Printed in Malaysia 066600035 3 CATEYE TOMO XC CYCLOCOMPUTER Model CC-ST200 [with Heavy Duty Wire] magnet sporkes bracket rubber pad Fig.1 Fig.8 MOUNTING TO BIKE Fig.9 lever #169-9731 Heavy Duty Wire and Bracket Sensor Kit #169-9771 Bracket Sensor Kit for Extra Large Fork #169-6168 Bracket Sensor Kit for Aero Bar #169-6167 Center Mount Bracket Kit #169-6169 Stem Mount Bracket Kit #169-9750 #169-9751 Attachment Kit (For Heavy Duty Wire) Attachment Kit (For TOMO XC) #166-5120 #169-6180 Wheel Magnet Lithium Battery(CR1620) SPECIFICATIONS Controller ----------------------------------- 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator) Display -------------------------------------- Liquid Crystal Display Sensor -------------------------------------- No Contact Magnetic Sensor Operating Temperature Range ------- 0°C - 40°C (32°F - 104°F) Applicable Cycle Sizes ------------------ 130cm - 229cm The length of the wire ------------------- 70cm Applicable Fork Diameter -------------- 11o - 40o (S:11 - 26o L:21 - 40o) Power Supply ----------------------------- Lithium Battery (CR1620 or CR1616) x 1 Battery Life --------------------------------- Approx. 3 years(The life of the first factory-loaded battery may be shorter than this period.) Dimension/Weight ------------------------ 1-15/16" x 1-25/32" x 5/8" (49 x 45 x 16 mm) / 0.74 oz (21 g) * The specifications and design are subject to change without notice. LIMITED WARRANTY 1-Year Warranty for Main Unit Only (Accessories/Attachments and Battery Consumption excluded) If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of charge. The service must be performed by Cat Eye Co., Ltd. To return the product, pack it carefully and remember to enclose the warranty certificate with instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and transportation charges to our service shall be borne by person desiring service. (Address for service) 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn.: CAT EYE Customer Service Section Service & Research Address for United States Consumers: CAT EYE Service & Research Center 1705 14th St. 115 Boulder, CO 80302 Phone : 303-443-4595 Toll Free: 800-5CATEYE Fax : 303-473-0006 e-mail: CatEyeUSA@aol.com CO.,LTD. E Slide the main unit onto the bracket from front until it clicks into position. To remove it, pull it off forward while pushing down the lever. (Fig.9) • The spokes must run correctly through the inside the magnet as in fig.1. • Attach the sensor with Sensor Bands-A-B to the right fork. Choose a band that fits the fork diameter (S size for up to 24o, L for oversize). If the front fork is thick, use the longer screw. 1. Insert the band-B into the slit of the band- A, and put the rubber pad inside of the band-A(fig. 2). Adjust the length in order that the screw-fastening part of the bands are parallel when mounted to the fork(fig. 3). *To pull out the band B from band A, tug strongly. 2. Mount the adjusted bands to the fork along with the sensor, by temporarily tightening the screw(fig. 4). 3. Align the magnet's center and the sensor's marking line(fig. 5), and make sure of 2mm clearance between the magnet and sensor (fig. 6). Then tighten the screw securely. Cut the excess of the band-B with a nipper or the like. • Secure the wire with nylon ties as shown in fig. 7. Wind the wire round the outer cable and wrap these wires with the spiral tube. Adjust the length of the wire. Loosen the wire in the area marked with the arrow so that the wire does not hinder handlebar operation. • Use either 1mm- or 2 mm-thick pads if necessary, according to handlebar diameter. Attach the bracket close to the handlebar stem (fig. 8). • Slide main unit onto the bracket from front until it clicks into position. To remove, pull it off forward while pushing down the lever. (fig. 9) •Test Mount main unit. If main display does not show any figures, press either M button or S/S button to release from power saving function. Spin the wheel to check if sensor pulse symbol flashes. If not, adjust relative positions of magnet and sensor following the instructions. TIRE SIZE L(cm) TIRE SIZE L(cm) TIRE SIZE L(cm) 20 x 1.75 150 26 x 1.40 200 650 x 38B 211 24 x 1 175 26 x 1.50 199 700 x 18C 207 24 x 3/4 Tubular 178 26 x 1.75 202 700 x 19C 209 24 x 1-1/8 Tubular 179 26 x 1.95 205 700 x 20C 209 24 x 1-1/4 191 26 x 2.00 206 700 x 23C 210 24 x 1.75 189 26 x 2.1 207 700 x 25C 211 24 x 2.00 192 26 x 2.125 207 700 x 28C 214 24 x 2.125 196 26 x 2.35 208 700 x 30C 217 26 x 1(559mm) 191 27 x 1 215 700 x 32C 216 26 x 1(650c) 195 27 x 1-1/8 216 700C Tubular 213 26 x 1.25 195 27 x 1-1/4 216 700 x 35C 217 26 x 1-1/8 Tubular 197 27 x 1-3/8 217 700 x 38C 218 26 x 1-3/8 207 650 x 35A 209 700 x 44C 222 26 x 1-1/2 210 650 x 38A 212 nyron ties Fig.7 outer ...
Écrivez votre propre critique du dispositif
|
|