Évaluations - 7, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Universal Mounting Bracket 2. Wheel Sensor 3. Computer Case with Installed Battery Thank you for purchasing this Planet Bike bicycle computer. Planet Bike will donate 25% of our profits from this purchase and any other Planet Bike products you buy to grassroots bicycle advocacy groups that work to improve conditions for cyclists. Enjoy your new Protege bicycle computer and thank you for making a difference! fnr* % of profits to iCJtt/ojcfe advocacy 4. Battery 5. Wheel Magnet 6. Quick Ties (6) 2. Computer Setup and Programming STEP 1: BATTERY INSTALLATION To install the battery, remove battery cover by inserting a coin in slot and twisting 1/4 turn counterclockwise (diagram #1). Install the battery (model CR2032 3V Lithium) with the"+" side facing up. Replace the battery cover, making sure that the rubber gasket is in place and the battery cover is flush with the battery case. Once again, insert coin in slot and twist clockwise 14 turn to secure battery cover. The battery should last for 6 months with normal use. The battery installed in sensor should last approximately one year. STEP 2: ENTERING PROGRAMMING MODE A) New Battery just installed: “M/M” or “KM/H" will already be flashing. Skip to step 3. B) Programing computer without replacing battery: Click the mode button (diagram #1) until “ODO” is displayed on line 4. Using the tip of a pen or the end of a bent paper-clip, depress the set button. Upon release, “M/M” or “KM/M” will flash in the upper right of the screen. Note: M/M equals F and 12 hour display, KM/H equals C' and 24 hour display. STEP 3: TO SELECT MILES/HOUR (M/H) OR KILOMETERS/HOUR (KM/H,) press the mode button. Press the set button to lock in your selection and the screen will display “2154” (or your current tire setting) with the last digit flashing. STEP 4: DETERMINING THE WHEEL SIZE SETTING (WSS) can be done in two ways. Please note that for WSS less than 1000mm, you must input your WSS in WSS 2 “ WSS 1 “ 0” does not allow a size less than 1000mm. For directions on WSS see step 6-7 below and additional features section in this instruction. METHOD 1: Read the tire size on the side wall of your tire and input the number that corresponds to your tire size on the tire size chart to the right. Since there are many tire manufacturers and designs, tires listed as the same size from different manufacturers can actually vary significantly in their actual circumference. Therefore, we recommend using method 2 for maximum accuracy in your computer readings. METHOD 2: Wheel Roll Out: For best results, find a flat smooth surface to perform the wheel roll out and inflate your tires to riding pressure. A) Place a piece of masking tape or draw a line on the surface to determine a starting position. B) Position the front tire valve at the 6:00 position (diagram #2) directly above the starting position. C) Roll the bicycle forward one revolution of the wheel on a straight line until the valve stem is again at the 6:00 position. (Note: Putting pressure on the handle bars to simulate body weight on the tire will give more accurate results). Mark the finishing position with masking tape or a line. Measure the distance between the starting and finishing positions in mm, this is your WSS. Repeat the procedure if necessary and average the results. (Note: If you use an inch measuring tape, multiply inches by 25.4 to achieve your WSS in mm.) STEP 5: INPUTING WHEEL SIZE SETTING © (WSS) A) Press “mode" button to change “flashing” first digit to desired selection. B) Press “set” button to lock in your selection and advance to the next flashing digit. C) Repeat steps A+B until all four digits are set. After the fourth digit is set, it will advance to the screen to Odometer setting. STEP 6: ODOMETER SETTING 0: The digit on the far right will be flashing. (If you don’t need to set the Odometer, repeatedly press “set” to advance to WSS ®.) Repeat steps 5A and 5B again to set the Odometer. STEP 7: WHEEL SIZE SETTING © (WSS): The screen will now display ® default WSS “0000” with the first “0” flashing. Repeat step 5 used to set WSS 0. Note: 2nd wheel size is not active if size is not entered. STEP 8: ODOMETER SETTING ®: Repeat step 6 to set Odometer 0. STEP 9: CLOCK SETTING: The hour digit on the far left will be flashing. Repeat steps 5A-5B again to set the time. To reset the clock only, press mode button until clock function is displayed on line four. Press "set" button to initiate clock reset. Follow steps 5A-5B above to set the time. When you are done, the computer case will enter normal operating mode. Now it's time to properly install bracket and sensor. TIRE SIZE WSS TIRE SIZE WSS 20x1.75 1502 700 x18c 2072 24x1.0 1750 700 x20c 2091 24x1.75 1894 700 x 23c 2105 24x2.0 1925 700 x25c 2105 26x1.25 1950 700 x28c 2143 26x1.5 1996 700 x 32c 2160 26x1.95 2055 700 x 35c 2168 26x2.0 2066 700 x 38c 2184 26x2.1 2070 700 x 40c 2200 26x1 (559mm) 1925 FOR FUTÜRE REFERENCE 26x1 (6...