Log:
Évaluations - 3, GPA: 5 ( )

Instructions Clarion, Modèle PSWFRGR

Fabricant : Clarion
Taille : 103.72 kb
Nom Fichier : PSWFRGR(Install),1.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


The advantage to using this type of amplifier is in the low current consumption of the amplifier at high power levels. The class "D" amplifier provided with this system will produce a rated 100W into a 2 ohm load. The woofer supplied with this system uses a voice coil with rated impedance of 2 ohms, and therefore is not considered a standard woofer. Replacing the woofer with any driver having an impedance greater than 2 ohms will yield lower power output from the amplifier, and is not recommended. PROCEDURE Proper installation of this product requires proper tools and knowledge of car audio principles. If you are not comfortable performing any of the outlined tasks below, contact a professional installation facility to perform the work. OUTLINE • Remove the head unit. • Connect the Clarion "T" harness between the radio and factory wiring and route the harness extension to transmission hump of the vehicle. • Install subwoofer enclosure. • Test subwoofer enclosure and head unit functions (fade, balance, dim, etc.). • Adjust subwoofer gain. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. 1 Ia. WIRING USING A CLARION “T” HARNESS Ia. WIRING USING A CLARION “T” HARNESS There are 2 methods to connect this product to the vehicle. Please refer to section Ia and Ib for each. • STEP 1: Remove the Radio. • STEP 2: Connect the "T" Harness. A. Unplug factory wires from radio. B. Plug the "T" harness in line with the radio wiring. SEE DIAGRAM 1. C. Connect the BLACK wire on "T" harness to radio chassis. • STEP 3: Route the wire harness from the radio to transmission hump of the vehicle. •STEP 4: Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure. STEP 5: TEST and SET the GAIN. A. Turn on the system and be sure all speakers are working properly. B. Set the subwoofer amplifier gain to a suitable level. Ib. WIRING USING THE SUPPLIED HARNESS • STEP 1: Remove the Radio. • STEP 2: Connect the wires. Yellow: Connect to Constant 12V Power Black: Connect to Radio Ground or Chassis Blue: Connect to Amp/Antenna Turn-on Lead Green: Connect to Left Rear Speaker (+) Positive Lead Green/Black: Connect to Left Rear Speaker (-) Negative Lead Violet: Connect to Right Rear Speaker (+) Positive Lead Violet/Black: Connect to Right Rear Speaker (-) Negative Lead • STEP 3: Route the wire harness from the radio to transmission hump of the vehicle. •STEP 4: Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure. STEP 5: TEST and SET the GAIN. A. Turn on the system and be sure all speakers are working properly. B. Set the subwoofer amplifier gain to a suitable level. 2 II. RUN WIRE HARNESS II. RUN WIRE HARNESS A. Route wire harness behind the drivers seat. B. Plug in Clarion”T” harness or hard wire pigtail harness in the dash. III. INSTALL THE BRACKETS TO THE ENCLOSURE A. Position enclosure upright. B. Locate the two horizontal dimples on each side of the enclosure. C. Screw in the attachment brackets through the dimples using the (4) supplied pilot point wafer head screws. IV. TEST THE ENCLOSURE A. Plug in the Clarion “T” harness or hardwire the pigtail harness behind the radio. B. Place the enclosure into the vehicle (correct position is on the transmission hump). C. Plug in the wire harness to the enclosure. D. Adjust subwoofer gain (gain pod is located on the amplifier next to the wire harness connector, and is adjustable with a Phillips screw driver). 3 V. ATTACH THE ENCLOSURE TO VEHICLE V. ATTACH THE ENCLOSURE TO VEHICLE A. Press enclosure firmly against the rear wall. B. Screw in brackets to the vehicle floor using the (4) supplied 1" self tapping screws. VI. REASSEMBLE THE VEHICLE A. Make sure all the wires are hidden. Then do the process in reverse order. Clarion Corporation of America 661 West Redondo Beach Blvd Gardena, CA 90247 800-Go-Clarion © 2000 Clarion Corporation, Gardena, CA 10 - PSWFRGR Rev. 1 (05/00) 4 ...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories