Log:
Évaluations - 3, GPA: 4.7 ( )

Instructions Wolf, Modèle PI363418

Fabricant : Wolf
Taille : 207.64 kb
Nom Fichier : 0f373bb4-51fb-a8d4-7dfa-32763978ea3c.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


The hood must overlap the cooking surface by a minimum of 3" (76) on either side. Installation of all Pro ventilation hoods should be 30" (762) to 36" (914) from the bottom of the hood to the countertop. Follow the dimensions shown in the Installation illustration on page 4. Wolf Pro island hoods are shipped without a blower assembly. Internal, in-line or remote blower assemblies are available. Blower options also vary with the volume of air that needs to be moved and the length of the duct run. Refer to the charts at the end of this section for Pro ventilation recommendations and blower options. IMPORTANT NOTE: Install this ventilation hood only with a Wolf blower. Pro island hoods require a separate, grounded 110/120 V AC, 60 Hz power supply. The service should have its own 15 amp circuit breaker. Placement of the electrical supply is not critical, as long as you provide enough 120 V AC, 60 Hz power cable to make the electrical connection. Location of electrical is centered through the top of the hood as shown in the Installation illustration on page 4. You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. Refer to the installation instructions shipped with each Wolf product for detailed specifications. This information can also be found on our website, wolfappliance.com. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Planning Information Pro Island Ventilation Hood MODEL PI363418(R) DUCTING CONSIDERATIONS Wolf Pro island hoods are shipped without the blower assembly. Internal, in-line and remote blower assemblies are available. IMPORTANT NOTE: Install this ventilation hood only with a Wolf blower. Pro island hoods have a vertical discharge location with 10" (254) round duct. A transition with backdraft damper is included. The hood will operate most efficiently when ductwork does not exceed 50' (15 m) in length. Local building codes may require the use of make-up air. Consult your local HVAC professional for specific requirements in your area. IMPORTANT NOTE: Wolf Pro island hoods must be vented to the outside. Use only metal ductwork. Refer to the illustration below for ducting considerations for Pro island hoods. Ducting for Pro island hoods. ROOF CAP OR REMOTE BLOWER 18" (457) HEIGHT OF HOOD ISLAND HOOD DUCTWORK INSTALLATION THROUGH ROOF 34" (864) DEPTH OF HOOD 10" ROUND DUCT VERTICAL DISCHARGE VERTICAL DISCHARGE ONLY FOR ISLAND HOODS. TRANSITION 141/8"W x 9"D TO 10" ROUND 7"H (INCLUDING FLANGES) SOFFIT, CABINET OR DUCT COVER 30" TO 36" (762–914) COUNTERTOP TO BOTTOM OF VENTILATION HOOD 36" (914) STANDARD FLOOR TO COUNTERTOP HEIGHT Dimensions in parentheses are in millimeters unless otherwise specified. 6 Planning Information Planning Information Pro Island Ventilation Hood MODEL PI363418(R) WOLF BLOWER ASSEMBLIES A ventilation system must include a blower assembly. Wolf ventilation hoods are shipped without the blower assembly. An internal, in-line or remote blower assembly must be selected to accommodate the cooking appliance, CFM requirements and homeowner preferences. Internal, in-line and remote blower assemblies are available as sales accessories through your Wolf dealer. IMPORTANT NOTE: Use only a Wolf blower with all Wolf ventilation products. Internal blowers are mounted inside the hood canopy. In-line blowers are mounted in between the hood and the exterior of the home. Remote blowers can be mounted on the roof or in some cases, on an exterior wall. Refer to the illustrations below for dimensions of Wolf in-line and remote blowers. Pro ventilation recommendation charts on the following page provide minimum CFM recommendations according to the cooking appliance and ventilation hood used and blower options for each specific Pro island hood. 18" (457) 22" 247/8" (632) 12" (305) 18" 8" (203) (559) (457) In-line BLOWER-110IL 241/2" (622) 151/2" (394) 281/4" (718) 203/4" (527) 243/4" (629) 14" (356) 43/4" (121) 10" (254) Diameter 143/4" (375) 291/2" (749) 291/2" (749) 18" (457) 22" (559) 101/8" (257) 71/4" (184) 10" (254) 10" (254) Diameter 143/4" (375) 291/2" (749) 291/2" (749) 21" (533) 25" (635) 103/8" (264) 71/4" (184) 10" (254) 10" (254) Diameter Remote BLOWER-60REM and Remote BLOWER-120REM Remote BLOWER-150REM BLOWER-90REM Unit dimensions may vary by ± 1/8" (3). Dimensions in parentheses are in millimeters unless otherwise specified. 7 Planning Information Planning Information Pro Island Ventilation Hood MODEL PI363418(R) PRO VENTILATION CFM RECOMMEND A TIONS Pro Island Hoods Model DF304 / R304 / SRT304 DF366 / R366 / SRT366 / RT366 DF364 / R364 / SRT364 / RT364 RT362 R488 / RT488 DF486 / R486 / SRT486 / RT486 DF484 / R484 / SRT484 / RT484 DF606 / R606 DF604 PI363418 600 PI423418 600 900 900 900 PI543418 1100 1100 900 PI663418 1500 1500 MinimumCFMrequirementsfor Wolfrangesandrangetops.CFMrecommendationsare based ontotal Btu/hr output. Additional CFMmayberequir...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories