Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
• Draw a horizontal line at 650 mm above the hob. Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. • Mark the wall at the centres of the holes in the bracket. • Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line. • Mark the wall at the centres of the holes in the bracket. • Mark a reference point as indicated at 116 mm from the vertical reference line and 320 mm above the horizontal reference line. • Repeat this operation on the other side. • Drill o 8 mm holes at all the centre points marked. • Insert the wall plugs 11 in the holes. • Fix the brackets using the 12a (4,2 x 44,4) screws supplied. • Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of 5-6 mm between the wall and the head of the screw. EN 29 Mounting the hood body • Before attaching the hood body, tighten the two screws Vr located on the hood body mounting points. • Hook the hood body onto the screws 12a. • Fully tighten support screws 12a. • Adjust screws Vr to level the hood body. Connections When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe o 150 or 120mm, the choice of which is left to the installer. To install a o 150 • To install the dumper 10 • Fix the pipe in position using sufficient pipe clamps (not supplied). To install a o 120 • To install a o 120 mm air exhaust connection, insert the reducer flange 9 on the dumper 10. • Fix the pipe in position using sufficient pipe clamps (not supplied). • Remove any activated charcoal filters. RECIRCULATION VERSION AIR OUTLET • Push fit connection 15 onto the hood body outlet. . • Insert the connection extension pieces laterally 14.1 in connection 15. • Make sure that the outlet of the extension pieces 14.1 is horizontally and vertically aligned with the chimney outlets. If this is not the case, adjust the position by either reversing the connection extension pieces 14.1 and then reassemble as described previously. • Ensure that the activated charcoal filters have been inserted. DUCTED VERSION AIR EXHAUST SYSTEM EN 30 ELECTRICAL CONNECTION • Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. • Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. . Chimney assembly Upper exhaust Chimney • Slightly widen the two sides of the upper chimney and hook them behind the brackets 7.2.1, making sure that they are well seated. • Secure the sides to the brackets using the 4 screws 12c (2,9 x 9,5) supplied. Lower exhaust Chimney • Slightly widen the two sides of the chimney and hook them between the upper chimney and the wall, making sure that they are well seated. • Fix the lower part laterally to the hood body using the 2 screws 12c (2,9 x 9,5) supplied. EN 31 USE Control board Key Function Display A Switches the motorselected speed on and off at the latest Indicates the selected speed B Decreases the suction speed. - C Increases the suction speed. - D By pressing this key it is possible to start the intensive speed from any previously selected speed. This speed has been timed at 10 minutes. After that time the system activates automatically the latest selected speed. This function is recommended for cooking condition where vapours and odours need to be eliminated immediately and quickly. HI and the remaining time appear alternately. The spot down at the right side flashes once a second. By pressing the key the function is stopped. E By pressing this key it is possible to set up the motor to a suction speed at 100 m3/h. During the intensive speed or the Delay-function this function cannot be activated. 24 appears and the spot down at the right side flashes while the motor is on. By pressing the key the function is stopped. F By pressing this key it is possible to set the delayed shutdown of the hood to 30 minutes. This function is suitable for a complete elimination of residual cooking odours. Functioning only when the motor is on(not during the 24Hfunction or intensive function) The suction speed and the remaining time before the hood shut down appear alternately The spot down at the right side flashes. By pressing the key the function is stopped G By pressing this key for about 2 seconds it is possible to reset the filter saturation alarm. After 100 working hours a FF appears. Metal grease filters have to be washed. After 200 working hours EF appears. Charcoal filters have to replaced. H By pressing this key the intensity of the lighting system can be decreased cyclically. I Switches on/off themaximum intensity. lighting system at the L By pressing this key the intensity of the lighting system can be increate intensit...
Ce manuel est également adapté pour les modèles :Ventilateurs - Hood KSE951X (466.46 kb)