Log:
Évaluations - , GPA: ( )

Instructions Metra Electronics, Modèle KIA OPTIMA 99-7324

Fabricant : Metra Electronics
Taille : 360.62 kb
Nom Fichier : INST99-7324.pdf

Langue d'enseignement: en

Le document est chargé, s'il vous plaît patienter
Le document est chargé, s'il vous plaît patienter

Facilité d'utilisation


2 - ISO Din Head Unit provision with Pocket...................... .3 Final Assembly ...........................................4 *Note: Refer also to the instructions included with the aftermarket radio. 99-7324 DASH DISASSEMBLY KIA OPTIMA 2006.5-2010 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the panel surrounding the radio including the a/c vents and climate controls. (Figure A) 3 Remove (4) Phillips screws securing radio. Unplug and remove radio. (Figure B) Continue to kit assembly. A 1 99-7324 KIT ASSEMBLY DIN HEAD UNIT PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly. 2 99-7324 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio opening until the side clips snap into place. (Figure B) 3 Snap the trim plate onto the front of the Radio Housing. (Figure B) Continue to final assembly. A 3 99-7324 FINAL ASSEMBLY FINAL ASSEMBLY (A) Strip wire ends back 1/2" B) Ttoist ends together C) Solder D) Tape 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METRA / EIA WIRING CODE 12V Ignition / Acc...... . . . . Red Right Front (+)...... ......Gray 12V Batt / Memory..... . . . . Yellow Right Front (-)....... ......Gray/ Black Ground.............. .... Black* Left Front (+)....... ......White Power Antenna........ . . . . Blue Left Front (-)........ ......White / Black Amp Turn-On ......... . . . . Blue / White Right Rear (+)...... ......Violet Amp Ground.......... .... Black / White Right Rear (-)....... ......Violet / Black Illumination .......... .. . . Orange Left Rear (+)....... ......Green Dimmer ............. .... Orange / White Left Rear (-)........ ......Green / Black *NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer's specifications. 4 () B C ■ - ) D V- ■MM -J 99-7324 NOTES 5 99-7324 INSTRUCTIONS 1-800-221-0932 y REV. 04/27/10 ©COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7324...

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories