Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Оденьте на них обод (3). Закрутите винт (2) в отверстие на ободе. РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ Этап 1: Установите подставку для вентилятора на сухую и ровную поверхность. Этап 2: Подключите провод к стандартной розетке переменного тока напряжением 220 В. Этап 3: Вставьте 2 батарейки типа АА в специальный отсек пульта дистанционного управления в соответствии со схемой, изображенной внутри пульта. СКОРОСТНЫЕ РЕЖИМЫ РАБОТЫ Для регулировки скорости воздушного потока нажмите кнопку ON/SPEED на контрольной панели вентилятора или на пульте ДУ: 1 - низкая скорость вращения; 2 - средняя скорость вращения; 3 - высокая скорость вращения. SWING (ВРАЩЕНИЕ) Возможна работа в стационарном положении и с поворотом на 90°. Для того чтобы головная часть вентилятора начала вращаться, нажмите кнопку ВРАЩЕНИЕ (SWING) на пульте дистанционного управления или кнопку на контрольной панели вентилятора. Для того чтобы остановить вращение, нажмите на эту же кнопку повторно. 6 ENGLISH SAFETY MEASURES 1. Never use this fan close to a water source (bathtub, washbasin, swimming pool...). 2. Never slip fingers, pencils or any other object through two grilles when the fan is in motion. 3. Disconnect the fan when moving it from one place to another. 4. Disconnect the fan prior to removing the grilles for cleaning. 5. Always ensure that the fan is placed on a stable surface to avoid it tipping over. 6. Never expose the fan to rain, water projections or damp. 7. If the fan's power cord becomes damaged, it must only be replaced by an After Sales Service technician or another suitably qualified person to avoid any safety hazard. ASSEMBLY INSTRUCTIONS • Please assemble correctly by the following orders when using. 1. Assembly The Stand • Screw the iron plate out of the standing shaft in anti-clockwise direction. • Put the standing shaft into the stand. • Screw the iron plate firmly from the bottom of the stand in clockwise direction and combínate the standing shaft and the stand well. 2. The Whole Assembly Link the fan main body and the standing shaft together by the fixing screw and then fix them. Loosen the fixing screw and pull the electroplated pipe to the height needed and then fix it firmly. 3. Rear Net Assembly - Screw the blade fastening screw out in clockwise direction and screw the net fastening screw out in anti-clockwise direction. - Fix the rear guard onto the three pillars of the motor front shell. - Screw the net fastening screw tightly in clockwise direction. 4. The Assembly of Fan Blade - Put the fan blade onto the electrical axle centre and the axle centre bolt must be pressed to the end of the concave notch at the back of the fan blade. They must be tallied completely. - Screw the screw into the electrical axle centre in anti-clockwise direction and then fix it. 5. Front Net Assembly • Put the hook of the front guard ring on the top of rear net. • Put the rear net into front make them tally completely. • Tighten the fastening screw of the lower of the front guard ring. USING THE FAN ON/SPEED: Press the key it will be in wind speed state, the related indicator light will be on. The following diagram shows the order of the wind flow: Weak -->Middle --> Strong 1 - LOW SPEED 2 - MEDIUM SPEED 3 - HIGH SPEED OFF - STOP Press the OFF key, all the working state will be cancel. TIMER Press this key it will be in wind speed state, the related indicator light will be on. The following diagram shows the order of the time setting: 1 hour--> 2 hours--> 4 hours. 3 1919.qxd 24.12.03 11:45 Page 8 e SWING Press the oscillate control knob, the fan begins to wave. Pull the button, the fan stops waving. SETTING THE TILT ANGLE Slack off the knurled screw on the ball joint, move the fan to the desired angle, then tighten the knurled screw down again. The remote control must face to the receiver: • The using range of the remote control must be within 8 meter away from the receiver. If the remote control isn't faced to the receiver, its using range will be narrowed. • If th...