Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
OPTIONAL RECIRCULATING KIT ALSO AVAILABLE. . FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE WWW.KOBERANGEHOODS.COM OR CONTACT KOBE RANGE HOODS AT (626) 350-1355. 3 INSTALLATION PLEASE READ ENTIRE INSTRUCTION BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to Table 1. (All calculation in inches.) -FOR UNDER THE CABINET TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Height of Counter Top to Hood Bottom (Recommended 27'' to 30'') [(A – B) – (D + E)] D = Height of Hood E = Height of the Cabinet -FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) TABLE 2 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Height of Counter Top to Hood Bottom (Recommended 27'' to 30'') D = Height of Hood E Height of Duct Cover F = Height of the Hood Installation [A – (B+C)] 4 SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: USING ELECTRICAL SCREWDRIVERS MAY CAUSE DAMAGE TO THE HOOD. Installation Table of Contents UNDER THE CABINET INSTALLATION................................................................................6 Preparation Before Installation................................................................................................6 Hood Installation ........................................................................................................................6 Ductwork Installation.................................................................................................................7 Wiring to Power Supply.............................................................................................................7 Final Assembly ...........................................................................................................................7 STAND ALONE INSTALLATION ...........................................................................................9 Preparation Before Installation................................................................................................9 Hood Preparation Before Installation .....................................................................................9 Hood Installation ........................................................................................................................9 Wiring to Power Supply...........................................................................................................10 Duct Cover Installation............................................................................................................11 Final Assembly .........................................................................................................................11 5 UNDER THE CABINET INSTALLATION Preparation Before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. • A straight, short vent run will allow the hood to perform more efficiently. • Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. • Temporarily wire the hood to test for proper operation before installing. • Important: Peel protective film off the hood, if any. • Use duct tape to seal joints between pipe sections. • For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not included) on each side. Refer to Figure 2. • Using references in TABLE 1 on page 4 and Measurements and Diagrams on page 18, create access opening for electrical wires and hood exhaust under the cabinet. Figure 1 Figure 2 Hood Installation Figure 3 CAUTION: If moving the cooking range is necessary to install the hood, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Puncture the knockout holes (for mounting under the cabinet) on the hood as shown in Figure 3. 2. Attach ducting transition to hood exhaust with ten (3/16” x 3/8”) screws (included). Shown in Figure 4. 3. If necessary, attach two rubber stands (included) with adhesive tape (included) to the back corners of the hood. 4. Draw electrical wires through cabinet access opening. 5. Center the hood beneath the cabinet and flush with the front of the cabinet. 6. From inside of the hood, place screw (not included) into the center of each knockout hole and secure to cabinet bottom. Once all mounting screws are in place, finish tightening screws until secure. CAUTION: MAKE SURE HOOD IS SECURE BEFORE RELEASING. 7. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more Figure 4 secure installation, use as many mounting holes as needed to secure from the inside of hood (screws not included). 6 Ductwork Installation Ductwork Installation 8. Use 8” round steel pipe (follow building co...
Ce manuel est également adapté pour les modèles :Ventilateurs - CH0036SQB (2.03 mb)
Ventilateurs - CH0048SQB (2.03 mb)