Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
d) You can fight the fire with your back to an exit. What to Do If You Smell Gas . Extinguish any open flame. . Do not try to turn on the lights or any type of appliance. . Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right away. CAUTION 1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors. 2) To reduce the risk of fire, use only metal ductwork. 3) Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities. Activating any switch on may cause ignition or an explosion. ELECTRICAL SHOCK HAZARD – Can result in serious injury or death. Disconnect appliance from electric power before servicing. If equipped, the fluorescent light bulb contains small amounts of mercury, which must be recycled or disposed of according to Local, State, and Federal Codes. 3 COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) RANGE HOOD BOX ORIGINAL KIT – Model No. RA1020DC (Sold Separately) . KOBE Range Hood - 1 . Warranty Registration Card - 1 . Instructions Manual - 1 . Baffle Filter - 2 (for 30”, 36”, 42” hood) - 3 (for 48” hood) . Bottom Casing - 1 (for 30” hood) - 3 (for 36” & 42” hood) - 2 (for 48” hood) . 7” Round Adapter – 1 . Oil Tunnel – 1 . . . . . . . . KOBE Adjustable Duct Cover - 1 . Screws Package – 1 . Duct Cover-Mounting Bracket – 1 Hood-Mounting Bracket – 1 . . . . OPTIONAL RECIRCULATING KIT – Model No. RA1020RD IS AVAILABLE. . FOR MORE INFORMATION, PLEASE CONTACT KOBE RANGE HOODS AT (626) 309-1356. 4 INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation Calculate the length of the installation, before installing the hood. (All calculation is measure in inches.) - FOR UNDER THE CABINET - TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Preferred Height of Counter Top to Hood Bottom (Recommended 27” to 30”) D = Height of Hood E = Height of the Cabinet - FOR STAND ALONE (WITH OPTIONAL DUCT COVER) - TABLE 2 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Preferred Height of Counter Top to Hood Bottom (Recommended 27” to 30”) D = Height of Hood E = Height of Duct Cover [F – D] F = Height of the Hood Installation [A – (B+C)] 5 SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY OCCUR. Installation Contents Under the Cabinet .................................................................................................................6 Stand Alone ..........................................................................................................................8 6 UNDER THE CABINET INSTALLATION Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. . Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. . A straight, short venting run will allow the hood to perform more efficiently. . Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. . Temporarily wire the hood to test for proper operation before installing. . Important: Peel protective film off the hood (if any). . For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not included) on each side. Refer to Figure 2. . Measure and create access opening for electrical wires and 6” round plastic exhaust under the cabinet. Hood Installation CAUTION: If required to move the cooking range to install the hood, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Puncture the knockout holes on the hood as shown in Figure 3. 2. Using references on Table 1 and measurements on page 14 center the hood in place beneath the cabinet and flush with the front of the cabinet. 3. Draw electrical wires through cabinet access opening. 4. From the bottom of the hood, place screw (not provided) into the exact center of each knockout hole. Make sure all screws are in place before tightening screws. CAUTION: MAKE SURE THE HOOD IS SECURE BEFORE RELEASING. Figure 1 Figure 2 . Figure 3 Figure 4 7 Ductwork Installation 5. Use aluminum or steel pipe to connect the 6” round plastic exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer to Figure 4. 6. To convert ductwork to 7” round, attached 7” round adapter (provided) to the 6” round plastic exhaust. Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAK...
Ce manuel est également adapté pour les modèles :Ventilateurs - CH-191 (1.78 mb)
Ventilateurs - CH9130SQB (1.78 mb)