Évaluations - 5, GPA: 4
(
)
)
|
Facilité d'utilisation
Hood Installation CAUTION: If required to move the cooking range to install the hood, turn OFF the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Using references on Table 2 and measurements on page 21-22, mark the leveling point of the hood. Position two mounting screws (not provided) on the wall, leaving 1/8” away from the wall as shown in Figure 26. Figure 25 Figure 26 2. Use aluminum or steel pipe to connect the exhaust opening at the rear of the hood to the ductwork. Use duct tape to make all joints secure and air tight. 3. Align hood-mounting bracket to the two screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. CAUTION: MAKE SURE THE HOOD IS SECURE BEFORE RELEASING. Duct Cover Installation 4. Mark the position of the duct cover-mounting bracket. Use calculation E from Table 2 for references. Attach and secure duct cover-mounting bracket with two screws (not provided). Refer to Figure 27. NOTE: Inner duct cover will cover the mounting bracket. 5. Connect electrical wires. Refer to “Wiring to Power Supply” on page 16. 6. Slide the inner duct cover up 2 inches before sliding the entire duct cover onto the hood. Refer to Figure 28. Mounting Screws 15 Figure 27 Figure 28 7. Adjust the height of the inner duct cover to the duct cover-mounting bracket. Secure the inner duct cover with two (4x8 mm) screws (provided) as shown in Figure 29. Figure 29 8. Fasten outer duct cover to multi vent exhaust on the hood with four (4x8 mm) screws (provided). 9. Continued at “Install Accessories” on page 16. Attach Together 16 Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 1. Connect the electrical wires. - If necessary to hide the electrical wire connections, push wires back into the wiring box. Access the wire connections underneath the hood by removing the bottom casing from the six screws. Before reattaching the bottom casing, make sure wires do not slip between motors, impellers, or any moving parts to prevent any damage. - Connect three wires (black, white and green) to house wires and cap with wire connectors. - Connect according to color: black to black, white to white, and green to green. - Test the operation of the hood before moving on to the next step. Make sure power is supplied to the hood. Install Accessories 1. Place the oil container (round) into keyhole under each safety screen. Turn clock-wise until firmly in place. Refer to Figure 30. 2. Slide oil container (oval) into plastic slot behind each safety screen as shown in Figure 31. Figure 30 Figure 31 Final Assembly 1. Turn power ON in control panel. Check all lights and fan operation. 2. Make sure to leave this manual for the homeowner. 17 OPERATING INSTRUCTIONS This KOBE hood is equipped with four electronic controls with a 10-second standby startup & 30-second delay shutoff, two powerful centrifugal turbine impellers with safety screens, two bright 12-volt 20-watt halogen lights, and four oil containers. The four electronic controls are Light Control, Speed Control A (cycles through Low, Medium, High, QuietMode.), Speed Control B (cycles through Low, QuietMode., High, Medium) and the Power Control (On/Off). Refer to Figure 32. Figure 32 Turn On: - Press Power Control (On/Off) button once. (If any Control button is not pressed within 10 seconds, power will be automatically turned off). - The KOBE hood will start on Low speed. Each press of the Speed Control button will cycle through the various speeds. - Press Speed Control A button to cycle from Low, Medium, High, or QuietMode.. Press Speed Control B button to cycle from Low, QuietMode., High or Medium. - Press Light Control button to turn halogen light on. Turn Off: - Press Power Control (On/Off) button once, panel lights will flash and power will be completely shut off after 30 seconds. OR - Press Power Control (On/Off) button twice, all power will be shut off immediately. - If only the lights are on, pressing Power Control (On/Off) button once will turn power off after 30 seconds. Speed Control A (Cycles through Low, Medium, High, QuietMode. ) Power Control Speed Control B (Cycles through Low, QuietMode. , High, Medium) Light Control 18 MAINTENANCE CAUTION: NEVER PUT YOUR HAND INTO THE AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. For the optimal level of operation, clean the range hood surface, safety screens, and oil containers regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve its fine appearance. 1) Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2) If hood looks splotchy (stainless steel hood)...
Ce manuel est également adapté pour les modèles :Ventilateurs - CH2236SQ (1.5 mb)