Évaluations - 4, GPA: 5
(
)
)
|
Facilité d'utilisation
Tighten screws. Connect 4” duct and vent to the outside. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. Pull wires through the strain relief. 13 Tighten the strain relief screws. 41722-01 3/29/2006 41722_EngS_3.29.03.indd 13 3/29/06 10:55:07 PM C23 F 1 2 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground C22 Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option • C24 G C25 H C26 H Connect wires as shown. Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. Tighten the wiring cover plate screw. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring from the motor to the wiring cover plate. 14 41722-01 3/29/2006 41722_EngS_3.29.03.indd 14 3/29/06 10:55:11 PM C30 E1 Go to step on page 18 to attach grille. C27 I C28 ON OFF C29 D11 EXISTING FAN E D12 Secure the motor by tightening the 2 screws. 15 Test the motor. If the motor does not run, check the plug connection. Turn on the power source. Existing Construction – accessible only from below Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (9”x 9.75”). Move the housing into position above the ceiling 41722-01 3/29/2006 41722_EngS_3.29.03.indd 15 3/29/06 10:55:14 PM D13 2 1 D14 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground D16 Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option Connect wires as shown. E D15 Pull wires through strain relief. Attach existing ducting to duct connector. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. 16 Screw pre-loaded screws into joist or framing. 41722-01 3/29/2006 41722_EngS_3.29.03.indd 16 3/29/06 10:55:16 PM • D18 G Tighten the wiring cover plate screw. D17 F 1 2 Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. D19 H D20 H I D21 D22 17 Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring from the motor to the wiring cover plate. Secure the motor by tightening the 2 screws. Turn on the power source. 41722-01 3/29/2006 41722_EngS_3.29.03.indd 17 3/29/06 10:55:19 PM K H E1 ON OFF D23 D24 E1 Go to step on page 18 to attach grille. E4 K H J E3 E2 L Attaching the Grille Test the motor. If the motor does not run, check the plug connection. Slide light mount over posts and attach thumbscrews. WARNING: To reduce the risk of electrical shock, all 4 thumbscrews MUST be properly installed. Remove the thumbscrews. Remove glass. 18 41722-01 3/29/2006 Connect wiring harness. 41722_EngS_3.29.03.indd 18 3/29/06 10:55:23 PM E6 L E5 J Align glass and push up. 19 Trouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sure it matches the wiring diagram. Problem: Light does not come on. Solution: • Replace the light bulb with a new bulb. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sure it matches the wiring diagram. Problem: Fan is noisy. Solution: • Check and tighten all fasteners. • Check the glass to make sure it is secure. • Check the flapper to make sure it moves freely. If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at 41722-01 3/29/2006 Install 2 Max 60 Watt A-15 bulbs (Not Included) and 1 Max 7 Watt C-7 bulb (Not Included). 41722_EngS_3.29.03.indd 19 3/29/06 10:55:25 PM Warranty Hunter Fan Company Bath Exhaust Fan LIMITED WARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan: If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within one year after the date of sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free of charge for parts and labor performed at our nearest service center or at our Service Department in Memphis, Tennessee. After this one-year period, you will be responsible for all parts and labor costs for repairs on the bath exhaust fan except for motor repairs as provided below. If your Hunter bath exhaust fan motor fails at any time within five years after the date o...
Ce manuel est également adapté pour les modèles :Ventilateurs - ELLIPSE 90063 (9.3 mb)