Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
If a B.S.1363 fused plug is used, it must be fitted with a 3amp fuse which is approved to B.S.1362. IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code: GREEN and YELLOW - EARTH BLUE - NEUTRAL BROWN - LIVE CORD CLAMP 3amp FUSE As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- The wire which is green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. As the appliance must be earthed, DO NOT use 2-pin socket outlets, if you are in doubt, consult a qualified electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size ie. 0.75mm2 cross sectional area and temperature rating of 85°C eg. heat resisting PVC. IF A MOULDED PLUG IS FITTED In the event of replacing a fuse in the plug supplied a 3amp ASTA approved fuse to B.S.1362 must be fitted. Note: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted. A new fuse cover can be obtained from your local Electrical Retailer. The colour of the correct replacement fuse cover is that of the coloured marks or inserts in the base of the plug. GB 6 GB 7 GETTING TO KNOW YOUR COOKER HOOD The Controls WARNING: Children should not be allowed to play with the appliance or tamper with the controls. a bcd e a Light Switches the lighting system on and off. b Motor Switches the extractor motor on and off at low speed. b+c Speed Increases the operating speed. b+c+d Speed Increases the operating speed. b+c+d+e Intensive Maximum operating speed. (see Fig.1) Features Control Panel Grease Filters Grease Filter Release Handle Light (Halogen) Vapour Screen Telescopic Chimney Air Outlet (used for Filter version only) GB 8 CARE AND CLEANING Before you clean your Cooker Hood or carry out any maintenance, switch off and remove the plug from the socket to disconnect it from the electricity supply. Grease Filters (see Fig.2) These must be cleaned once a month using non aggressive detergents, either by hand or in the dish-washer, which must be set to a low temperature and a short cycle. When washed in a dish-washer, the grease filter may discolour slightly, but this does not affect its filtering capacity. To remove the grease filter, pull the spring release handle (f). Carbon Filters (see Figs.2 and 3) It absorbs unpleasant odours caused by cooking. The active carbon filter must NEVER be washed. The active carbon filter should be changed every 4 months in normal use. Mounting and replacing the Carbon filters: a. Disconnect the hood from the electricity. b. Remove the grease filters (Fig. 2). c. If Carbon filters have not been previously installed, place one active carbon filter on each side so that they cover the grates protecting the rotor on the motor. Then turn the centre handle in the clockwise direction (Fig. 3) to lock the filters in place. d. If the Carbon filters have already been installed (covering the grates protecting the rotor on the motor) and need to be replaced, turn the central handle in the counter-clockwise direction until the Carbon filters are unlocked. e. Refit the the metal grease filters. Replacing Lamps (see Fig.4) Firstly, if the lights do not work, make sure that the lamps are fitted properly into their housings. If they still don not work they are easy to replace. Replacement bulbs are available from Hotpoint Genuine Parts and Accessories (see Key Contacts, back page). Only use halogen bulbs of 20W max (G4), making sure you do not touch them with your hands. Access the light compartment: extract the guard by levering it off with a small screwdriver or similar tool (fig. 4). Make sure that the lamps have cooled before replacing them. Replace the burnt out light bulb. Close the lamp cover (it will snap shut). Cleaning • Clean regularly, with a sponge soaked in warm water and a sodium bicarbonate solution, which is among other things a good disinfectant. If you do not have any, you can use a neutral soap. • DO NOT use abrasive detergents, bleach or detergents using ammonia. NEVER use solvent based products. WARNING: Failure to carry out the basic standards of cleaning and replacement of the filters could cause a fire risk...