Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Fit the plug into the power socket. CONNECT DUCTWORK Adjust the width of the flue mounting bracket using screws (A) indicated in Figure. Use screws (B) and wall anchors to secure flue mounting bracket to the ceiling as shown. FLUE _,_OUNT_NG BRACKElr SCREWS B SCREWS A Ducted Configuration 1. Use 6" round metal duct to connect the duct collar on the hood to the ductwork above. 2. Use duct tape to make all joints secure and air tight. 3. Insert the decorative flues setting them on the hood. 4. Extend the upper flue to the ceiling and secure with the 2 screws (C). -, FASTEN FLUE TO _,_" UPPER BRACKET "-WITH SCREWS (C) DECORATIVE FLUE /DUCTTAPE 6"ROUND METALDUCT Ductfree Configuration 1. Turn upper flue sect{on upside down so air vents are at the top. Slide upper flue section into lower flue section. 2. Connect the duetfree pienum to the upper flue section with (4) flat- head screws (supplied). 3. InstalI the reduction on the discharge collar. 4. Measure the distance from the top of the reduction to the ceiling. Cut a length of 5" round metam duct 5" shorter than this dimension. 5. Fit duct section over the ductfree plenum. For best fit, make sure duct seam is toward the front. 6. Set duct/flue assembly on hood with top tilted away from wall. Reach around flue to engage bottom of duct with discharge UPPER FLU E SECTION X [ DUCTFREE PLENUM .... FLUE SECTION 5" METAL DUCT D_SCNARGE COLLAR AIR UPPER VENTS BRACKET (nn upper fUue section) collar on hood. Tilt flue up against wall. Duct seam can be cut to length if necessary. 7. Extend the upper flue to the ceiling and secure with the 2 screws (C). DUCTFREE FILTER INSTALLATION 1. Ductfree filter kit (B03300487) is included. 2. Position the filters over the blower. 3. Rotate to lock filters in place. -DUCTF'REE F_LTERS MAINTENANCE Proper maintenance of the Range Hood wilI assure proper performance of the unit. Grease Filter The grease fiBter should be cteaned fre quendy. Use a warm detergent solution. Grease filter is dishwasher safe. GREASE FILTER Remove filter by pushing filter towards the back of hood and rotating filter downward. Ductfree Filters The ductfree fiiters should be changed every 6 months. Rotate the fiiters to remove and replace. Hood Cleaning Stainless steel is one of the easiest materials to keep clean. Occasional care wilI help preserve its fine appearance. Cleaning tips: ,, Hot water with soap or detergent is all that is usually needed. ,, Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks. ,, For discolorations or deposits that persbt, use a non-scratching household cleanser or stainless steel polishing powder with a little water and a soft cloth. ,, For stubborn cases, use a plastic scouring pad or soft bristle brush together with cleanser and water. Rub Iightly in direction of polishing lines or "grain" of the stainless finish. Avoid using too much pressure which may mar the surface. ,, DO NO'[ allow deposits to remain for Iong periods of time. ,, DO NOT use ordinary stee! wool or steel brushes. Small bits of steel may adhere to the surface causing rust. ,, DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless stee! for extended periods. Many of these compounds contain chemicals which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth. Painted surfaces shouid be cleaned with warm water and mild detergent only. OPERATION Controls The hood is operated using the slide controls under the bottom of the hood. The light switch turns the lamps on and off. The blower switch :makes it possible to select the motor operating speed. Position O: motor off. The pilot mamplights up whenever the blower is on. LIGHT BULBS This range hood requires two 40-Watt light bulbs (included). ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY BEFORE CARRYING OUT ANY OPERATIONS ON THE APPLIANCE. To change bulbs: 1. Remove the screw securing the light fitting. 2. Replace with Hght bulbs of the same type+ CAUTION: BULB MAY BE HOT! LIGHT BLOWER SWITCH SWITCH WARRANTY Hfwithin 1 year from the date of installation, any part of this range hood fails to function properIy due to a defect in material or workmanship, Sears will repair the part or furnish and install a new part, free of charge. FULL 30_DAY WARRANTY ON F_NtSH ON PAINTED OR BRIGHT METAL PARTS Hfwithin 30 days from the date of instaiIation, the finish on any painted or bright metal parts of this range hood is defective in material or workmanship, Sears wiII furnish and install a new part, free of charge. WARRANTY SERVICE _S AVAILABLE BY CONTACTING THE NEAREST SEARS SEVICE CENTER/DEPARTMENT JNTHE UNITED STATES. This warranty appiies onty whiIe this product is in use in the United States= This warranty gives you specific IegaI rights and you may have other rights which vary from state to state. Sears, Roebuck and Co., Dept 817WA, Noffman Estates, IL 60179 ADVERTENCIA INDICADO PARA EL USO EN COCIN...
Ce manuel est également adapté pour les modèles :Ventilateurs - 233.503032 (1.14 mb)