Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
Instruction Leaflet % INFO-LINE If after having read this leaflet, you have any questions or comments on your fan, call 1-800-788-5350 in North America. FAN SAFETY PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS. IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1) Read all instructions before using the appliance. 2) To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet. 3) Keep the cord out of heavy traffic areas. DO NOT let the cord hang over the edge of a table or counter. To avoid fire hazard, NEVER put the cord under rugs, near heat registers, radiators, stoves, or heaters. 4) To protect against electrical hazards, DO NOT immerse in water or other liquids. Do not use near water. 5) Close supervision is necessary when any appliance is used by or near children, or by disabled people. 6) Always unplug the fan before moving it, putting on or taking off parts, cleaning, or whenever the fan is not is use. Be sure to pull by the plug and not the cord. 7) Avoid contact with moving parts. DO NOT operate without fan grills properly in place. 8) DO NOT operate any appliance with a damaged cord or plug, if motor fan fails to rotate, after the appliance malfunctions, or if it has been dropped or damaged in any manner. Return appliance to manufacturer for examination, electrical or mechanical adjustment, or repair. 9) DO NOT operate in the presence of explosive and/or flammable fumes. 10)Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by Bionaire® may cause hazards. 11) DO NOT use outdoors. 12)Always use on a dry, level surface. 13)Keep unit away from heated surfaces and open flames. 14)WARNING: To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-state speed control device. 15) DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC (Alternating Current)PLUG (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact qualified personnel to install the proper outlet. DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG IN ANY WAY. ASSEMBLY INSTRUCTIONS Tools Required: Phillips Head Screwdriver BASE/POLE ASSEMBLY Step 1. Insert the large foot bracket ( U ) into the bottom of the lower pole. Make sure to align the rectangular plastic tab with groove inside the pole. Slide the foot up approximately two inches and then screw the feet into place. Step 2. Insert the small foot bracket ( X ) into the bottom of the lower pole. Make sure to align the rectangular plastic tab with groove inside the pole. Slide the foot up until it touches the bottom of the upper foot bracket. Then screw the small foot bracket into place. A. Grill Hub B. Decorative Cap C. Security Screw D. Front Grill E. Fan Blade Cap F. Washer/Nut G. Fan Blade H. Rear Grill Mounting Nut I. Rear Grill J. Motor Shaft K. Motor Housing L. Speed Control Knob M. Fan Neck N. Clasp Screws (2) S. Extension Pole Bracket/Height Adjustment Knob T. Lower Pole A B C D E F G H I J K L M N O P Q R S T U V W X Y O. Extension Pole Clasp P. Power Cord Clip Q. Extension Pole R. Pole Cover, Extension Pole Bracket U. Large Foot Bracket V. Large Foot Extensions W. Rubber Feet (4) X. Small Foot Bracket Y. Small Foot Extensions 2 FAN HEAD ASSEMBLY Step 1. Attach the neck of the fan to the upper extension pole. To do this, align the extension pole clasps and screw holes up with the corresponding holes on the neck of the fan. Once you have the neck adjusted to the angle of the extension pole clasps, screw the clasps to the neck of the fan until secure. Step 2. Using your screwdriver, remove the securing screw that is located inside the Bionaire® decorative cap on the grill ring. Once you have unscrewed the grill ring, put it aside until you are ready to reattach the grills. Step 3. Remove the two plastic ties that are holding the rear grill and the fan blade together. Discard the two plastic ties and cardboard. Step 4. Loosen and take off the rear grill mounting nut ( H ) that is attached to the motor housing by turning counter-clockwise. Step 5. Place the rear grill on the front of the motor housing; making sure that the handle on the back of the grill is above the motor housing (doing this will align the holes on the grill over the two screws in the housing). Then tighten the rear grill mounting nut onto the rear grill ...