Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG IN ANY WAY. ASSEMBLY INSTRUCTIONS A. Grill Hub B. Front Grill C. Fan Blade Nut D. Fan Blade E. Rear Grill Mounting-Ring F. Rear Grill A B C D E F G H I J K P Q L Figure 1 BSF1731 G. Motor Shaft H. Motor Housing I. Upper Pole J. Height Adjustment Knob K. Lower Pole L. Base Insert M. Base N. Weighted Insert O. Weight Nut P. Fixed Screw Q. Grill Ring R. Remote Control Housing S. Fan Post Screw T. Remote Control M N O I K S R H GT J Figure 2 BSF1731RC BASE/POLE ASSEMBLY Step 1: Insert lower pole into the base until the threaded end of the pole protudes through the opening in the center of the base. Twist the pole clockwise until locked. Step 2: Turn the base upside down and place the weighted insert into the base by aligning it between the two parallel ribs. Secure the base, weight, and pole system together by tightening the weight nut to the threaded portion of the pole. Place the base on the floor, right side up. Step 3:Replace the height adjustment knob over the pole, slide it down the pole, and secure it to the base by turning clockwise. FAN HEAD ASSEMBLY TRIM CAP Figure 2 Figure 3 Figure 4 Figure 5 Step 1: Position the rear grill over the motor shaft, making certain the cut outs in the center of the grill fit over the prongs on the motor housing. Please make sure the rear grill fits securely against the motor housing. Step 2: Secure the rear grill in its place using the rear grill mounting- ring. Turn this ring clockwise and tighten firmly. Step 3: Slide the fan blade, with the hollowed interior of the blade facing toward the rear grill, firmly onto the motor shaft. Make sure that the pin through the motor shaft aligns with the groove in the back center of the fan blade. Step 4: Secure the fan blade onto the motor shaft by firmly tightening the fan blade nut. NOTE: TURN THE FAN BLADE NUT COUNTER-CLOCKWISE Step 5: Align the tabs on the grills, and press grills firmly against each other. (Figure 2) Step 6: Place grill ring over attached front and rear grills with connecting link centered over the top of the grill. Make sure to fit the grooves on the underside of the grill ring over the edge of the front and rear grills. (Figure 3) Step 7: Secure the grill ring to the front and rear grills using the fixed screw. Place the trim cap over the connecting link and snap into place. (Figures 4 & 5) FINAL ASSEMBLY FOR REMOTE VERSION Step 1: Slide the remote control housing over the upper pole and secure the housing with the fan post screw. FINAL ASSEMBLY FOR NON-REMOTE VERSION Step 1: Slide the threaded end of the fan head pole, into the top of the pole. Holding the neck of the fan, turn it counterclockwise until it locks into position. NOTE: Make sure the top of the upper pole is facing away from you when placing the fan head into the pole. OPERATING INSTRUCTIONS FOR REMOTE VERSION Step 1: Insert 2 AAA batteries into the back of the remote control. Remote Control: Your remote control requires 2 AAA batteries for operation. To install the batteries, simply depress the back of the remote with your thumb on the spot marked OPEN. Insert batteries according to the diagram shown inside. Replace cover. Step 2: Set the fan base on a dry level surface. Step 3: Plug cord into any standard 120V AC outlet. Step 4: To turn the fan on press the POWER button on the remote control or on the touch-key pad. Step 5: The speed is adjustable by pushing either the speed button on the remote control, or on the SPEED button on the touch-key pad. Push this button first for LOW, again for MEDIUM, and a third time for HIGH. Push a fourth time to repeat the sequence. To turn the fan OFF, push the OFF button on the remote control, or on the touch-key pad. Step 6: To oscillate the fan head, push the button marked OSCILLATE on the remote, or OSCILLATE on the touch-key pad. Push a second time to stop oscillation. Step 7: This fan is equipped with a 4-setting timer. (1hr, 2hr, 4 hr, 8hr). To activate the timer, push the TIMER button on the remote control, or the TIMER button on the touch-key pad. Continue to push the TIMER button to cycle through your setting options. Push the button twice to repeat the sequence. Step 8: For a natural breeze movement, push the button marked MODE on the remote control or the touch-key pad. This BREEZE mode will imitate wind gust by varying the fan speeds between fast and slow. By pressing the MODE button a second time, you activate the SLEEP setting. This function slows the fan speed down, and when used in conjunction with the timer settings, will ultimately turn the fan off. Press the Mode button a 3rd time for BREEZE and SLEEP combined. NOTE: Timer can be used in conjunction with several other functions. For example: Sleep + 4hr. TIMER causes the fan to gradually slow down over 4 hours and eventually turn off. OPERATING INSTRUCTIONS FOR NON-REMOTE VERSION Step 1: Set the fan base on a dry, level surface. Step 2: Please make sure the Speed Control Knob is in t...